Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi,
I have nrf52840 on my custom board (Based on IMX6, Running Yocto linux) which is connected over UART.
I want to an OTA of zephyr OS on that chip over serial and for...
We have a custom device that we profile with a PowerProfiler (external DUT). Device is battery powered.
We have a strange idle current: cca 5 uA for 2 min, then 900 uA ...
Hello,
I am new to the nrf9160. i am quite confused in between nRF Thingy91(pca20035) and nRF9160DK (pca10090) .
What are the steps i need to follow to get start with...
Hello:
I want to change uart0 tx and rx pin from default 28 and 29 to 10 and 11.
I know the i2c pin change need to change nrf9160_pca10090ns.overlay in app.
So I tried...
For quite a while I've noticed that across multiple custom boards using the nRF52 I've been seeing low-level current spikes from a part that is in SYSTEM_OFF mode. They are...
i got 'LIS2DH12_ADDR' undeclared (first use in this function) error when i build my project but i already define it in pca20020.h file.
this image is i define about...
Hi,
I found the TRACE connector on nRF52833 and 52840 DK has its pin 9 connected to ground.
But in the datasheet of JLink/JTRACE, the TRACE connector has following pinout...
Hi,
Could you tell me where can I find some guide how to add DFU into NRF BLE examples, e.g. ble_app_proximity ? I would like to add DFU like a service into the app, not...
We are having a very difficult time soldering the nRF52840 to the PCB. Our Operations Department is asking what the lead finish of the BGA balls is. Would be great to get...
Hi,
I compiled and downloaded GPS sample, I got the following messages:
Tracking: 0 Using : 0 Unhealthy : 0
Seconds since last fix: 600
Scanning [ _ ]
Over 10 minutes...
Dear All,
I have noticed the following behaviour:
When the modem goes to PSM, it is not possible to retrieve the RSRP, using the CESQ or the XMONITOR AT commands. This...
Hi,
I am using NRF52840 DK in our project . I am using 15.3.0 SDK and soft device s140 in our project .Here the nrf52840 dk board is client and other controller bluetooth...
Hello,
SDK: 15.3.0
Hardware: nRF52840-DK
I am attempting to make a simple dimmer with 2 pins/LEDs. I have used the following post.
https://devzone.nordicsemi.com/f...
After following all the steps on the nRF Connect v3.2.0 Getting Started Assistant.
I get the following error after pressing OK.
Any idea what is wrong?
Am I missing...
