Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
currently i'm dealing with problems with this https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/1300 pull request which have wrong title and wrong changes ...
Hi everyone!
I'm wondering, is FSK compatible with the nRF52832. I want to emit 2 differents frequencies that the receiver will be able to recognize. If yes, How to create...
Location: Utah.
Well, I was testing a Thingy:91 board here with the very first boot and test with the iBasis SIM card which comes with the product.
Everything goes...
Hi,
I have qestion about crystal 32.768 kHz follow schematic as attached file.
Is it nessary to use ?
Is it possible, Can I remove this crystal ?
Thank you
Best...
Hello,
I am working on application where client sends the data to server in mesh, all servers are receiving the data as per the group subscriptions. Now, i have added the...
This link in nordic nrf connect apps is old version. There is no enable services for now. It should be changed to enable CCCDs. After enable it , data will be received in...
I tested the NFC transceiver APDU of the project nfc_uart is good. Then I ported the NFC code to the project ble_app_uart. When the board is simulated, the program pointer...
Hi,
I can use the SPI master functionality within nrf_drv_spi.c/.h just fine (i.e. calls from main) until I connect to my nRF52840 and utilize NUS. If I try to issue a nrf_drv_spi_transfer...
Hello,
I am working to implement the BLE stack for a HID keyboard, borrowing/based off the supplied example "ble_peripheral/ble_app_hids_keyboard".
Stack initialization...
In SEGGER Embedded Studio I am not able to connect to the J-Link anymore.
The error message says No idcode detected.
The J-Link commander program returns the following...
The SysTick port for NRF52 does not support tickless idle on freeRTOS, what is the reason for this limitation? Are there any known problems behind this limitation?
I tested the code below to make the board go to sleep and wake up on each button press. When I start, it draws 30ua, but when I press the button it shoots up to 200ua (a clear...
Hi,
We are developing nrf9160 sensor based product powered by primary battery(non rechargeable). Sensor current consumption is less than 1 mA.
while trying Saft LS14500...
Hello,
How can i put out the received Adv Data on the UART? Currently I get for every advertise packet the BLE_GAP_EVT_ADV_REPORT in my ble_stack_handler. Then i wanted...
