Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hi,
I'm wondering if the current nRF sniffer firmware (v3.0.0) can detect extended advertisements on arbitrary channels? Is it supported in the firmware? If so, can I use...
Hi all,
I did not do mesh SDK for a long time. Now when I see SDK Mesh, I saw Low power Node example. It can run with Mesh network and update OTA by DFU buttonless (I don...
Hi,
I had an experience with embedded programming but never with wireless technology. I am using Nordic SDK v16.0.0 and nRF Mesh SDK v4.0.0.
Here is a short description...
Hello All,
I am working on the Nrf52810 board with sdk 14.2.
I have implemented the read ,write , delete feature in my code.
Now it is creating new entry for repeating...
Dear All, I am trying to compile an application based on the Zephyr project for the nrf52. I am following the instructions from here .
I am using Windows. Using SES everything...
Thanks in advance.
Hi guys am working with nrf5282 (softdevice s132 V1.6.0 and SDK version 15.2.0), also enabled freertos, and also make softdevice changes rleated freertos...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
As part of my Factory setup we want to download MBR, bootloader, SoftDevice...
Hi,
I would like to perform DFU over Mesh. I am following the steps
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v4.0.0/md_doc_libraries_dfu_dfu_quick_start...
Hi,
anyone help me.
I am facing the issue during DFU with OTA. the steps are listed which had I done,
here trying to update softdevice.
1. Erase all.
2.flashed softdevice...
hey guys,
I want to write a c code to display temperature sensor data which is inbuilt in the nrf52840. I am using segger embedded studio. Can I get some reference code...
SDK: 15.3.0
Softdevice: S140 6.1.1
Brief usage: multi protocol radio driver 1.5.0, uart1, spi1, twi1, saadc, ble, gpiote 2 inputs, pwm1
I have been finding high current...
Hi,
I'm running into issues with the watchdog never firing. I'm using SDK v15.3.0, with S132 v6.1.1, and a custom bootloader (based off secure_bootloader example).
The...
I can successfully download an image using nrfutil dfu serial when I use a test image compiling the bootloader with the Nordic default public key.
I cannot successfully...
