Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I use S130 on two nrf51822/PCA10001 boards. Each nRF scans and advertises simultaneously.
Scan parameters are:
scan_param.active = 0;
scan_param.selective = 0;
scan_param...
Is there a port of lib_aci for 16-bit processors? The structs in lib_aci written for nRF8200 are byte misaligned using a 16-bit processor. Seems to be almost a complete rewrite...
Hello,
I try to generate 4 PWM signals on an nRF51 DK board, but I have two troubles :
in the "Simple PWM", during nrf_pwm_set_value() function the TIMER is stopped...
Hi,
I recently ordered a usb dongle. It has PCA10031 board. The chip shows "N51422 QF ACAB" printed on it.
What SDK should I use? 6.1.0?
What board file should...
Hi!
I am using nRF51 SDK v6.10. I try to analysis the "spi_master_example". Source codes is
working well. But I couldn't understand how the "spi_master_send_recv_irq(...
I have an android application, which one can set and unset the LEDs of my nRF51422 EK. But sometimes when I click to fast the command will not be send. So I would like to...
Hello,
I want to know if it is possible to configure a button to act with different Detection delay.
In other words I want to have a single button to be able to trigger...
Do we have KiCad version of nRF51822 QFN48 reference design? We looking at open source toolkits, including Eclipse, so KiCad comes into picture.
Thank you in advance!
The test code:
int main(void)
{
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, softdevice_assertion_handle);
temp_init();
unsigned int aaa...
I have a follow-up to this question: devzone.nordicsemi.com/.../
We are interested in dynamically changing the supply voltage because our space-constrained design requires...
Hi,
For my custom PCB, I am using the PCA10004 as reference in order to determine if the maximum possible range has been achieved. However, I am seeing only about 20 feet...
Hello I'v just ordered a NRF51-DK kit.
I'm looking at the different tool chain. In my application speed is critical 16Mhz is actually bearly enough, so my question is:...
I have a USB dongle with an nRF24LU1p that has a few SPI pins but is missing the RESET pin. I would like to be able to program it via SPI but the SPI programming protocol...
nRF51 RTX 4.74.0-3
SoftDevice S210 V4.0.1-3
Created a timer for 5 seconds interval.
It turned to be 4.4 seconds. with or without softdevice enabled.
Anybody else has...
Hi,
Access to the UART hangs the execution of the experimental_ble_app_uart_s110_pca10028 example.
The phenomen occures In the file simple_uart.c when checking for the...
