Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi,
Master device is whole the time in receive mode and I have a problem with read data from device which address is in Pipe1. IRQ appear and status is 0x4e and FIFO status...
Hello, I bought the nRF51822 Development kit and the nRF6700 starter kit and I'm having trouble finding tutorials on how to use the 2.4 GHz radio mode on the nRF51822. Can...
Hi everyone,
I have some strange behavior with a central peripheral combination. My central subscribes notification on the peripheral. This has a limited TX-Buffer for just...
Hi,
I am developing the nRF51822 for the BLE device application. For the data delivery I am implement this function based on "button_radio_example(Tx/RX)" example code. It...
Hello,
I have been since many days desperately trying to set the bytes in the advertisement packets in my Arduino, combined with an NRF8001.
What I am trying to achieve...
Hi,
I would like to connect my msp430f1611 with NRF8001 bluetooth module and send data with an SPI communication. I found an interesting guide here with the main part of...
Can someone from Nordic (or anyone who knows) comment on what happens when scanning and advertising simultaneously with S130. For example:
Scan Interval 100ms
Scan Window...
What are the conditions that can cause
sd_ant_burst_handler_request(Channel_0, 8, tx_buffer, BURST_SEGMENT_END) to return NRF_ANT_ERROR_TRANSFER_SEQUENCE_NUMBER_ERROR? If...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
Hi,
I developed application whitch is using S130 soft device. On central side to manage devices, i've used device manager from sdk 6.1.0. It works fine.
But now i need...
I tried to upload application through BLE DFU in MCP. The DFU Android app works fine. However, it always failed in MCP.
SDK 6.1.0
SoftDevice 7.1.0
MCP 3.7.1.8567...
Hi,
I have following use case. The write operation on one of the characteristics triggers some UART job which takes about 1 / 1.5 seconds to complete. After the completion...
Hello,
I try to use the S310 V2 but got stuck into problems.
in order to start the application from bootloader in the S310 V1 I did succesfully :
void (*application...
Hi,
I have problem on compiling bootloader example which is located at
\Nordic\nrf51822\Board\nrf6310\device_firmware_updates\bootloader
When I try to compile the...
Hi,
Some questions in example ble_app_hids_keyboard/main.c
Why set the adv_params.timeout to zero in BLE_DIRECT_ADV (Line 779) ?
That will cause no BLE_GAP_EVT_TIMEOUT...
