Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I am using softdevice-7 and SDK 6.1 for our application. I want to implement static key pairing for serial port over ble application "ble_app_uart".
I have implemented...
I have a 384 byte, writable, variable length, vloc user characteristic and I want to trigger an event when the write completes so my application can operate on the data. ...
Hello-
I am trying to program a custom nRF51822 board with a J-Link-lite.
From the J-Link-lite, I am using the 10-pin header and have it wired like this:
I'm using pins...
I have a situation where I need a software PWM for several channels, which are multiplexed via a shift register.
The output loop needs to run at several kHz for this to...
Because of the limitation in the GPIOTE hardware that only one channel can be connected per GPIO , care must be taken when changing a PWM duty cycle. If for instance the compare...
Links: https://devzone.nordicsemi.com/documentation/nrf51/6.1.0/s110/html/a00081.html#ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection，I don't Know how it works...
Hi Nordic
I do not know why sometimes program can build pass in keil ,but can make nrf51822 do not work and unable download program . For this , I have damaged a lot of...
Does the nrf51822 support 2 spi masters (on different pins)? I want 1 spi channel to talk to one set of peripherals, and the other to talk to another set. I see SPI_MASTER1_ENABLE...
Maybe question similar to this one devzone.nordicsemi.com/.../
Can I use the interrupt generated by RADIO_IRQHandler(void) while implementing another protocol?
At the...
Hi everyone,
for our current project we have to implement some sort of activation lock. Therefore, we would like to use the MITM security mechanism of BLE. The idea is...
I have an nrf51822-mkit.
Let's say there are 2 BLE phones continuously searching for my module. Phone 1 connects and communicates with the module. The modules determines...
I used the ble_app_lbs example as a template, with a PCA10003 eval board (nrf51422 chip). SD 110, Nordic SDK V6.1. Keil uVision 5.
I launch my application and my board...
Hi,
In softDevice S120 can we make second sd_ble_gap_connect on different peer, without waiting confirmation connect of the first one ?
Bests Regards,
Jérôme
Hi
NRF51822 with SD7, S110.
I have some troubles with DFU procedure. I uploaded standard OTA-DFU bootloader and S110 to my NRF. Everything works well with my code except...
