I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Is there any example combining the Serial and Over the Air DFU for the SDK13?
Or the posiblity to combining the two features into a single bootloader?
What steps should...
Iprogram the bootloader.hex to 0x78000 with jlink.Then in my application program,I set the NRF_UICR->NRFFW[0] register as belew:
static void write_uicr_customer_register...
When power on,run app first at 0x1f000,then reset and run to boot loader at 0x78000,how to set UICR registers to make this come true?I try to set the NRF_UICR->NRFFW[0] in...
Hello,
I want to build a system which will use 2 nrf8001 to communicate. 1 nrf8001 will act as a client by continuously transmitting its UUID and another one will act as...
I am working on RTLS project. I want to perform DFU in beacons but not getting proper information .I went through ( devzone.nordicsemi.com/.../) but i think it i for SDK 13...
I have a hex string like this 58FF1CE5.This is corresponding to One date time 16/09/1955 .(ie in MM/dd/yyyy).How can i do this in ObjectiveC, I am getting this date in didDiscovercharacterstivc...
After some search I found that accepted values for tx power are -40, -30, -20, -16, -12, -8, -4, 0, and 4 dBm.
So my questions are
once I set the tx power using ...
I will code 1 to 2, however, was not successful
code1 :
u8 IICwriteBytes(u8 dev, u8 reg, u8 length, u8* data){
u8 count = 0;
IIC_Start();
IIC_Send_Byte(dev);...
Hello Nordic Team,
I would like to know if it is possible to do a DFU of my SDK10 based application ( s130_nrf51_1.0.0_softdevice + SDK10 Bootloader ) on an nRF51822 (32...
Hello to everyone in this community,
I am new with NordicSemi chips and I have the Development kit 52832. I opened the example folder from the SDK 13, SPI slave and i saw...
Hii all,
I am working on a project where I need to store data to persistent storage and retrieve back when the board is restart. but now we are migrated to simultaneous...
hi, our company has developed bluetooth device based on nrf51822 chip with softdevice s130 8.0.0. Also, our company is sensitive to certification costs because it is a small...
Hola community, I am using nrf52DK for the first time and am unable to connect it to my mobile phone using Bluetooth. The problem I am facing at the moment is, the device...
Hi,
Currently I have a problem with the use of 52832 I2S interface to transmit voice, the transmission is not coherent.
Here is my initialization code
// Enable reception...
