Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
Using nRF52 with SD 132 3.0.0.
Peer manager uses fstorage to store information.
I need to be able to specify the address range which fstorage can use.
Is there a configurable...
Hi,
I have problem with both functions sd_ble_gatts_value on central device.
It works on peripheral, because there is my characteristics definition.
Now I have to read...
Hello,
I'm developing a BLE Application where I use the peer manager. My Goal is to use direct advertising after disconnection if a device already has bonded. But every...
I am using the SAADC on the nRF52832, SDK12.2.0, with it set to 12 bits and low power mode. I have enabled five channels which I run blocking nrf_drv_saadc_sample_convert...
Dose this capture from the Nordic Specification means that to read bytes from SPI i need to send before. Each byte i send i get a byte!!!
MLy case i have read only sensor...
I am using the nrf52832 with the s132 for a project in which I have a frame with 24 bytes that need to be transmitted through BLE.
I have followed the tutorials and I have...
Hi,
First I'd like to salute the great work done by you Nordic people for those open source and hardware.
I just installed the SDK 10.0.0, S120, gcc-arm toolchain, configure...
Hello, I'm a beginner with the BLE technology and nRF52 is a good tool to start with it.
Currently, I have a setup that allows a Raspberry Pi and an nRF52 to communicate...
Hi. I have a problem with programming brand new chips nRF51422.
I have connected: Vcc (1, 12, 35, 36), Gnd (33,34,13), Swdio (23) Swdclk (24).
christal on the board:
...
I had downloading many versions SDK,from 10.0.0 to 12.2.0.But when I Program SoftDevice then download the examples,such as the path:
nRF5_SDK_12.0.0_12f24da\examples\ble_central_and_peripheral...
hi,all.
when i first time connect nRF52840PDK to PC, and open nRFgo Studio, but encounter this problem:
no device detected.
screenshot:
I click recover button many...
I want to send several packages in one interval from my iphone to 51822(s130).But the demo ble_app_uart can only receive 1 package per interval（ipone6，lightbule，writewithoutreponse...
I want printf the date and time when compiling code.
But I drag on this error:
SEGGER_RTT_printf("%s %s.\r\n", __DATE__,__TIME__);
compiler says:
It's strange...
Hi engineer,
I found that the SAADC current is increased after the SAADC function opened, then my processing method as below:
1,I close SAADC function after sampling...
Looking for the OpenOCD equivalent of ""nrfjprog --rbp all"
Looking at the commands for OpenOCD they have a "flash protect" command, but it doesn't appear that's quite...
