Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I'd like to output some audio data through i2s. It's quite easy to understand your examples provided on infocenter, however, I can't get my code to work.
Here is...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I need to take data from sensor board through uart and send to mobile through ble for every 500ms. Sensor...
Hi guys
I want connect nrf51822 (Raytac MDBT40) by my phone(HTC battery one android 4.4.2).
I use softdevice 130(ver.2.0.0) and SDK 11 demo code under KEIL ARM 5.
...
when i run sudo nrfutil dfu serial -pkg my_package.zip -p/dev/ttyACM0 i get the following error:
pc_ble_driver_py.exceptions.NordicSemiException: Failed to send init packet...
Hi
I am working with mbed targetting for ReadbearLab Ble Nano. I am trying to encrypt payload before sendind it with:
include "nrf_ecb.h"
...
int main(void)
{
...
Hi, i'm using keil and i would like to run the fpu_fft example to perform a fft. The example works if I set 128 or 256 as number of input vector data as you can see in the...
I'm using SDK 6 + S110 v7.
Is it possible to use device manager to perform bonding but don't write bond information persistently in flash?
With old bond manager I could...
Could someone please guide me through the process?
I believe it can be done through nRF Studio which I have downloaded, but don't know how to proceed from there???
Tks...
Dears,
I am developing a ANCS application with nus service on our product. There are a few problems I don't know how to fix it.
My problem is that :
1. ANCS will not disconnect...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
I have request similar to this questions but for SDK13:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
Judging by quick grep sdk_config.h from ble_app_template...
I am having some trouble getting the Power Profiler to start up correctly. Currently, I have the PPK DK plugged onto the PCA10040 DK. All of the onboard switches are set to...
