HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hello, I've obtained and assembled a board with nrf52840 as its centerpiece, I'm here to ask what I need to compile my program for this relatively new chip?
Here is a list...
Hi,
Is there a way to determine which channel is currently being used by the nRF24LE1? i can't do hal_nrf_read_reg(RF_CH) because that function isn't exposed by hal_nrf...
Hi,
What is the best way to read the state of an output pin? I have an LED connected to a pin and want to know in a different part of the program whether the LED is currently...
I am having an app_timer (nRF52832 / SDK12.0.0) that's interval must be changed during its lifetime. I am using following code to change the interval:
app_timer_stop(m_timer_id...
Hi,
I'm trying to use the command "mlme_start_req" to setup the device as a pan coordinator to send beacons to the others devices in the network, but after submit the command...
Hello,
In my application, a peripheral will be connected to many central devices, and the application includes buttonless dfu service.
It needs pairing (encrypted connection...
Hi,
I have a device with nRF52832 and firmware is composed of Bootloader (BL), softdevice (SD) S132 v2.0.0, application and I am using SDK 11.0.
I have created different...
Currently, we are trying to have the nRF51 chip working with a type of capacitive pressure sensor. We did quite a lot of work on searching proper circuits of reading the capacitance...
I have 2 board nrf52840 DK, I now I want to send file ( 1~2 Mbyte) from board_1 to board_2 without use UART. where can I get example to do that ?
PS: I also need example...
I've merged the experimental_ble_queued writes sample code into my project and am testing the long write characteristic with nrfConnect from an Android phone. I get no errors...
Hi,
I am trying to figure out the reboot reason on an NRF52 in order to solve it in the best way.
We have a design with a dual supply 3.6V/5V going through a 3V LDO...
Hello,
i have a BLE Peripheral that has a service that we use to simulate UART over BLE. Very similar to the nRF UART. I consider the time to establish a link that allows...
Hi all,
I am trying to save an UART variable I am receiving. My case is very similar to the example Flash Write Example, but I would write few bytes instead of the whole...
Hello!
I have to sample audio signal from a microphone (MAX 9814 adafruit) with the nrf52 board. I use the saadc and then I perform a FFT of the data using the sdk 13 examples...
