I am working with a SD NAND with nrf5340dk using toolchain and SDK version 2.7.0. I am using the mass sample from zephyr. It seems like the SD card could be recognised and...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
A few years back I used a multilink project developed by one of the Nordic support personnel, to allow using the nRF52840 devkit board to talk to one of several Peripherals...
Hello,
I am having some trouble with the UART API (Async and interrupt). I am connecting the development board (nrf9151 DK) to a 3rd party device (keypad / prox reader)...
I'm trying to buy more data for my iBasis SIM cards that are provided with the nRF9160. I have 4 registered SIM cards and it was easy to buy more data through iBasis in the...
I'm working on an ESL project using the nRF5340-DK. I need to enable the PAwR feature, which requires Bluetooth 5.4. However, my current program is written using nRF Connect...
Hi Nordic Team,
am I currently evaluating the nrf5340 development kit for our new product revision and fail to get a power efficient shell besides rtt logigng.
Concrete...
First of all, let me say that I've read some of the other topics, and I clearly don't belong here haha. I'm not at all knowledgable about electronics and the inner workings...
I wonder if a couple (or three) of your module with PCB antenna as receivers could be used for triangulating the transmitter, could I have some hints about this, or a schetch...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello, I would like to know if the adress byte that is transmitted after the preamble is the MSB or LSB.
I've read the datasheet's page 28 and it's not very clear, it just...
I need to have an iOS device send my nRF51 some commands, some settings, and retrieve some data, not at regular intervals. The nRF51 should only-speak-when-spoken-to.
I...
Hi guys,
I want to use the nRF51822 as a gateway to send uart-commands from the µC to my iPhone and vice versa.
µC---|uart|--->nRF51822 ) ) ) ) BLE ( ( ( ( iPhone
...
Hi,
I am using the NRF51822-CEAA flip chip package for my custom board.
Because this package has an optical vulnerability from the sides, could you please advise how...
Hi developers,
I recently had a problem with nRF51822 and radio interrupts.
My situatios is quite clear but I cannot resolve the problem. I hope You will help me.
Description...
hi,everyone.
because of careless,i enabled pin reset in debug mode by set bit 0 in RESET register in my software,and i downloaded the hex file to a 51822.now,because of resetting...
Hi all
According nRF51822 Product Specification , GPIO pin can config to SPI interface. Means if I set a specific GOP pin range to SPI and connect these pins with...
I am successfully sending data from the PCA10001 Evaluation Kit to the Master Control Panel. But I cannot find any information about initiating and sending data from the MCP...
Hi,
Here i am attaching my text file. in my case timer api is working
but button event handler is not calling.
Kindly tell me , what is my fault.
Regards
Balaji...
I want to store a block of data in nRF51x22. I tried the following:
void HalStoreNVMBlock(uint32_t size, uint8_t* pBuf)
{
nrf_nvmc_page_erase(NRF_UICR_BASE);
nrf_nvmc_write_bytes...
I'm using the TWI module. Where can I set whether the DSA SCL pins have the internal pull-up enabled or disabled? I can't even find where to see if they are enabled at all...
