Hello, my application requires very precise timing to trigger an action on the edge of the GPS time. I just need to get this time once in a while to synchronize the system...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hello all, i made a board with this BLE chip:
nRF52832-CIAA-R
What happens is that when i enable power supply i can see the circuit is properly in advertise ( i can scan...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
I am developing a project using the nRF54L15 DK to interface with an ST25DV64KC NFC tag (specifically the Class 3 or Class 6 daughterboard from the ST25DV64KC-DISCO kit)....
I have a project migrating to nrf Connect from ESP-IDF. We need to recreate a system to work with existing devices on BLE Mesh, but I am having trouble figuring out how to...
Dear colleagues, I am using the Nordic nrF9151-DK as part of assignment 2 of the intermediate Devacademy course. This assignment is about trying and using the various vscode...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
What should be format of USER Certs for Matter factory data?
CONFIG_CHIP_FACTORY_DATA_CERT_SOURCE_USER =y
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
We are using nRF5340 with nRF7002 on our custom board. Our application requires:
Wi-Fi (via nRF7002)
Thread (via nRF5340)
DFU over Wi-Fi
We are concerned...
We have peripheral, and we want to connect it using NRF 52840. when we are bonding this using nrf connect app we get a pop up with random key and using pair we can pair with...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...