Hi,
I am power profiling an application on the NRF52 DK. The application uses SPI to communicate with the BMA400 accelerometer:
The program initializes the accelerometer...
Hello I have a custom board with LR1110 Lora radio I'm getting errors that driver is not supported when I define the spi1 for it
lora0: lora @ 0 {
compatible = "semtech...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Dear Nordic Team,
I am programming with ncs V2.9.0 and nrf52833.
There is a trouble happend when one side delete the pairing info,but the other not.
Peripheral has already...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
Hello,
I am truing to store data in the UICR register "customer area" from application code. The procedure is invoked only once when the registers are still empty. The...
Hello all,
In controlling two devices simultaneously from one central controller, I have noticed significant time delays in processing the second call to sd_ble_gattc_write...
Hi.
I am using PCA10028 board an SDK10.0.0.
nRF51's Max flash size is 256KB.
Q1. "s130_nrf51_1.0.0_softdevice.hex" size is 302KB already. How can we make HEX file less...
Hi.
I'm using PCA10028 and SDK10.0.0, S130 v1.0.0.
And "ble_app_hrs_c" example is my reference code.
It works well before i add code for timer as below.
void start_timer...
Hi I am an student who is a poor fledging embedded engineer.
I met an error on using nrfgo studio
when I click the tab [Device]-[nRF5X Programming]
I used JLink_V510p...
Hi,
Using ble-app-uart sdk9 example:
Is there a difference where I initialize uart in main? My code is able to run when I shifted the uart_init() after ble_stack_init...
Hi,
I am trying to figure out which GPIO pins i can use as UART on a nrf52 chip if i put it on a custom PCB (Not DK !!). From the reference manual (page 513, 48.10.7 and...
hi,
i want to restart my timer before it expires.
suppose my timeout is 2 second and i want to restart it in between 0-2 second based on signal when i receive before expires...
I've notice that the ST Balun NRF01D3 that I've used for my current design is not listed as compatible with Rev 3 (Build code: H) nRF51822 Silicon. Has there been any change...
Hi everyone,
I am looking into Crossworks and SEGGER's Embedded Studio and since they are related I am wondering which one of them is more recommendable? Right now Eclipse...
Hi,
I have set ble_adv_fast_timeout = 0 (same problem with ble_adv_slow_timeout) to get advertising forever, but when in call sd_ble_gap_adv_start, i get error 0x07 (param...
Hi all
According the nRF51822 Product Specification V3.1, the 16MHz RC oscillator has a tolerance of at most 5% and can be used as clock source for the UART module.
...
Hi,
I am trying to change an example code on ble_app_uart_c (Central) SDK10.0.0 s130.
I have changed already peripheral example and I can see notification data if I...
