I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
I am implementing the whitelisting feature so that the NRF52 only pairs with one phone at a time. We require the NRF52 to advertise for 10 mins but I could only set...
IN looking at CONN_SUP_TIMEOUT below:
It says the units are 10 ms. if you take 4000 * 10 ms, you end up with 40000 ms which = 40 seconds - not 4 seconds.
Also for...
Hi,
As title, I'm the new for this.
I have one 52840 board and several 52832 boards, and one of them(sink) collect some data from other boards by using proprietary radio...
Hello,
We use nRF52832 with SDK-11 as peripheral in our project. We want to utilize white-list feature to limit the connection establishment. I have studied H ID Mouse example...
Hello, I'm trying to view the STATUS register of the timer (1 for example) but it is not display on the segger registers view ... Is it a well known problem ? Cheers, Sylvain...
I am developing application on nRF52832 with SDK14. I came across mem_section_dummy_rom and mem_section_dummy_ram sections in the linker script in the example codes. I couldn...
Hi
I have been using nRF52 in my project. I am not using provided uart drivers for one uart -> UARTE1. I am using DMA access and I have no problem to send and record messages...
Hello,
Can the nRFgo tool be used to compile/construct Gatt profile & service tables for nRF8240 devices.
If not is there a tool for construction the services (e.g. like...
Dear Sir,
Please tell me how to configure the NFC pine P0.09 & P0.10 as GPIOs. I followed all the procedure given in the development kli manual & on the nordic blogs also...
Dear Sir,
I am using nrf52832 & sdk 14. When I dump your twi sensor code(SDK14\nRF5_SDK_14.2.0_17b948a\examples\peripheral\twi_scanner\pca10040\blank\arm5_no_packs) in the...
Hi ,
Need a bit of help here.
I am trying to use TWI and SPI in a single code for communicating with two different slave devices, the LTC2941 coulomb counter and the EM4325...
I've adapted the SPI example to read a value from an Analog Devices ADXL350 accelerometer as follows:
But when connected to the accelerometer this hangs waiting for the...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
