Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Dear all,
I'm a quite new BLE stack user and need to get some idea on the idea behind service discovery.
I'm using the S130 and the BLE central example and want to read...
Hi,
We are going into mass production with our first product and would like some expert advice on what is the best approach.
1.) Since we would be doing production tests...
Question for anyone familiar with mBed code on nRF51 devices (I have cross posted on mBed, but trying my luck here too):
I'm developing an nRF51822 program using the nRF51...
Hello, I am trying to upload my custom firmware to the MetaWear RG (nrf51822) platform but currently without luck. Steps that I have performed:
Connected to the device...
Hi,
I want the bonding to happen between the nrf51 and the Android Phone by displaying passkey on the phone. This can be done using device manager or peer manager. When...
I haven't really found too much referencing how to setup an Eclipse DFU Bootloader project for Debugging.
What I know
To get the image to fit in the allocated memory...
HiNordic,
I found nrf5-sdk-for-eddystone Project in github,but it's just surpport nRF52832.I want to know where to find the nRF eddystone SDK which can surpport nRF51822...
We're working on getting our nRF52 app working with buttonless OTA updates and the bootloader. OTA works fine with the example bootloader, but when we extend our application...
Hi, I Converted experimental dual bank signed bootloader into single bank signed bootloader and it uploads the new firmware successfully but the problem I got is it erases...
I have an application programed on the nRF 52DK (PCA10040). Its a UART communication to a distance sensor. The Problem is, that I cant send anything from the uC to the Sensor...
Hello,
I just run in following issue. I try to configure an UART to send some bytes. To check the configuration, I just let the program loop, after the sending. Attached...
Hi all! I have a smart beacon kit rev 1, with s110 on it (the latest firmware available). I am using the RTC with the 32 kHz crystal (50ppm) to trigger an ADC conversion every...
After releasing reset to the nRF51, its UART is responding with
RX: A4 1 6F 1 CB
Further requests for things like capabilities, etc go ignored, and opening a working...
hi all,
i cant able to find the version 11 softdevice hex file. can you please send the link.
and can i use the version 8 softdevice for version 11?
-Thanks in adv...
In the migration guide, I can read: "Clearing an interrupt event may not take effect immediately."
And an example of required code is given as:
NRF_TIMER0->EVENTS_COMPARE...
