Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
We currently have an application that is running SDK 12.1 on the NRF52832. We have no issues doing a firmware update using the iOS SDK. What we are seeing is a long delay...
Hello, I am running bluetooth example.
I am using the nRF52832 board and SDK 14.0.
I modified the multilink example to make a slight modification and connect it to another...
I have a windows side application and an Android App, both of which are set to capture data from the Thingy Sound Service.
On the windows application, the data after being...
I need to be able to reserve some flash to permanently store manufacturing values that will never change. I did this on an nRF51 by reserving a 4KB block and setting the necessary...
Hi all ,
I have problem . I have 1 NRF52832 dev kit . It connect to STM32 devkit via UART . I want to tranfer firmware of STM32 from smartphone to NRF via BLE , and from...
Hi,
I added this in SystemInit() (just below the CONFIG_NFCT_PINS_AS_GPIOS section) within system_nrf.c so that I could easily turn on or off the APPROTECT read back protection...
I am using Thingy 52 and I need to use multiple sensors on the board. But the API reference is really poor and there is no examples on this. So I don't know how to configure...
I'm trying to debug a high current issue on a custom board based on the nRF52832. I'm currently loading a modified blinky app (entire main.c included below). On the nRF52DK...
hello,
I am using nrf52 DK and MPU 9255 .I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in...
Hi all,
I have a Thingy52 and a nRF52-DK.
I have successfully setup 2 different Eclipse projects to compile code for both hardware.
On the nRF52-DK, i was able to build...
I am developing Firmware for NRF51822, S110 in Eclipse. I Heard that there is two mode in Firmware. 1. Debug mode 2. Production(release) mode. Is there anything like that...
Hi,
Currently I am browsing the mesh sdk to get enough information for my own implementation,
However sometimes its quite difficult to see what a C/H file actually does...
Hi,
I am trying to use nRF52832 dev kit(pca10040) as my connectivity board and STM32L4 as my application board. I have flashed ser_s132_uart(examples\connectivity\ble_connectivity...
Hi,
I have seen alot about the declaration process with the Bluetooth SIG but couldnt find my specific case.
We made a BLE application with the NRF51, a PCB Antenna, SD130...
