Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using NRF51822 with soft device version 6.0.
I'm trying to create an event which should be triggered every 24 Hours. In the current implementation in our code base...
I saw the demo of nRF52832 connected 20 peripheral devices and control the light in the peripheral.I would like to know the more deatil of the whole operation in chip/SD....
I've searched and the majority of answers seem to be years old.
I have an existing app_timer event handler that works perfectly, blinking LEDs.
I will soon have another...
Hi! I'm using two RedBear Nano v2 and I'm trying to read a long characteristic from one of the two devices. As I read in other posts in the forum, I need to invoke the read...
If I'm not mistaken, both S110 and S130 support OTA DFU right?
I understand that nordic semi most likely recommend S130 over S110, but please understand that
my current...
I have previously developed on the nRF24LU1+. This device would have a CHIPID in the InfoPage, This ID would have guaranteed it does not violate the requirements for ESB addresses...
Hi, im using NRF52832 whit SDK 12.3.0, when i compile this error appear, "undefined reference to `nrf_drv_spi_init", i included the "nrf_drv_spi.h" file.
also try to include...
Hi everyone,
I'm working with nrf52832 and i'm trying to send data over BLE for communicate with a mobile app. I saw that we could pass data with the function ble_nus_string_send...
Minor nitpick:
The PS_v1.0 datasheet says that "see the Reference Layout section on the Downloads tab for nRF52840 on..."
There is no Reference Layout section on the Downloads...
I am working on a BLE bootloader using SDK 14.2.0 on an NRF52832 device, using softdevice version 5.0.0. I am able to get the bootloader up and running, and I am able to see...
Pre Conditions:
1. As soon as the connection is established the App start a timer to disconnect the link using sd_ble_gap_disconnect
2. The app timer has the same timeout...
Hello,
I'm searching the possibilities of Thread mesh network. And I want to minimize the size of border router as small as possible. Have you considered to port the border...
Hi,
I'm having trouble writing to a characteristic when operating as a central. I'm sure it is just a lack of understanding on my part but neither the SDK documentation...
Dear Sir,
In the twi sensor example code in sdk14 of nrf52832 the sensor LM75- B is mentioned.Please tell me that can I use LM75-A. with the same code.
Warm Regards, Manoj...
