Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hi, I have created my own hardware with nRF54L15 – 2xLED, 2xPWM, and Radio (BLE). I am trying to create a custom board using the graphical wizard. LED and PWM seems to work...
I have an external GPS module connected to an nrf9151dk over UART. The module is correctly powered, and sending messages over its tx pin, which has been confirmed by attaching...
I´m trying to change the installation path of the Nordic Power Profiler as I´m running out of space.
I have about 9GB left, but when trying to open a captured file, Power...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
Hello,
I would like to measure the current consumption of my nRF9161 and compare the result with a standard measurement. While searching in your documentation, I found this...
I'm having trouble enabling BLE DFU on my firmware for the nRF52833. I'm following the steps from the Dev Academy course - FOTA over Bluetooth Low Energy . After adding the...
Hi
Could I use 3.3V to the C3 capacity in the application example,datasheet?That is to say,C3 doesn't connect to VDDPA pin and 3.3V connect to the C3.I found that it is...
We have developed our custom nRF8001 board and connected with Arduino UNO bord. we have used nRF HRM demo application from Github . We are using nRF utility application from...
OK, I didn't read enough fine print before I plunged in, but my version of the nrf51822 I have on a bunch of boards isn't supported by the new SDK.
In a premature onset...
I'm trying to use notifications with Android 4.4. When my service issues a call to sd_ble_gatts_hvx, the result is BLE_ERROR_GATTS_SYS_ATTR_MISSING.
From this link , I...
Hi
when i call twi_master_transfer function in for(;;) loop of file ble_app_hrs project.
Kindly tell me what to do for that.
for (;;)
{
for(i=0;i<10;i++)
{
...
When I plug the PCA10000 into my mac I can see it presents 3 USB interfaces. The first is interface class 0x02, Communication Control, the second is 0x0a, which is Communication...
Hello
I have problem to reach 100 feet and a high data rate using BLE.
I am thinking about using gazell. Is possible to communicate with gaxell protocol to IOS and Android...
Hi guys,
I am trying to get the maximum packet size out of my nrf24 radios. If I am implemeting my own radio protocol which doesnt require 3-5 bytes of address is it possible...
Note that nWP-018 "Migrating to the latest nRF51822 chip version" specifies that the SDK version which should be used with the Eval Kits I have (version 1.0, chip variant...
I'm using the nRF51822 with the version v5.2.1 S110 soft device and have implemented a communication scheme that is very nearly identical to the Nordic UART protocol as implemented...
Hi,
I'm currently working on an Android 4.3 app who must communicate with a model of a specific device.
This device contains a Bluetooth low energy chip nrf8001 and there...
Hi,
I have a problem when running 51822 with Nrf toolbox on android 4.3 Samsung S4. The problem is that the BluetoothGattServer disconnect itself after 30 seconds. The...
Hello all currently i am setting a Client Characteristic Configuration value to indicate to retrive value from device. but in some device refuce to give value . so first i...
