Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi,
I am working on RTC implementation. I had a doubt.. Is it possible to generate interrupts on different channels (channel 0/1/2/3) using same RTC instance ?
Thanks
Hello,
I'm trying to communicate with another device via I2C. I'm trying to do a simple write but it seems that the TWI NRFX driver is sending wrong data.
I'm just calling...
Hi,
I am implementing a beacon solution and intrested to move from fast to slow and vis versa(slow to fast) advertising modes -
i.e. BLE_ADV_MODE_FAST & BLE_ADV_MODE_SLOW...
Hey,
I have seen some articles which says that voice over BLE (4.0) is possible but there is no standard profile for it.
So far i've seen :
Silicon Labs
STM
T.I...
Hi,
After I reset nrf8001, RDY pin stays hi. I checked the crystal pin, there is no clock. I am using TSX-3225 from Epson with 12pf caps.
Am I suppose to see the clock...
Hi,
I am working on a new project with the secure bootloader (SDK 15) as a part of it. I want to add periodic task that will do several actions for example maintaining the...
Hi,
I am downloading my code to my custom board and sending commands through a USB virtual COM port. I basically echo and execute some GPIO operations after decoding the...
I have installed NRF 5X command line but I don't see it in my programs/start / desktop where will be the .exe file or how can I open that? How can I work with that ?
Hello ,
I am using 4 nrf52 DK for Mesh
1. how to I configure a Node as Relay
2. How do I capture MESH Packets/ Data from Mesh in Raspberry Pi and send to cloud
hi,
When working with Keil are the NRF_SDH_CLOCK_LF_RC_TEMP_CTIV & NRF_SDH_CLOCK_LF_RC_CTIV compiled as part of the nrf52810_xxaa project?
if not how can I compile...
Hello, is there a way to send messages via the mesh transport/access layer (not using client/server models) but still be Bluetooth SIG compliant? where can I find information...
Hello,
There are a few posts about EasyDMA consuming 1-2mA of current, and I've measured similar currents. In the nRF52832 product specification, this appears to be one...
Hello,
I am running the ble_app_beacon example and want to add battery percentage in the advertising packets, how to do that. And is it possible for ble_app_beacon example...
I had planned on using the nRF52840 I2S peripheral in Nordic Master mode to either produce a 31.25 kHz sampling rate, or a 62.5 kHz sampling rate for my application.
There...
How do I make my phone to auto connect to my nrf51822 device when it is within range ? I dont want to keep having to tap connect on my app. (android and IOS)
