here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Good Morning Team,
Hope your day is going well!
Could you please provide the IPC 1752 document and RoHS CoC (2015/863/EU) directive document for below part since it is...
hi hi ;
i'm trying to control gpio pin 20 with my smart phone and with event at gpio pin 5 (when the state of the pin 5 changes the gpio pin 20 toggeles ) but my problem...
Hi, can someone explain in simple terms how it works?
I don't really have a clear concept of what a replay attack is, but I suppose it has something to do with recording...
Hi,
I am facing the same issue for all of the node.js examples.
It says: Connected! Error: command disallowed (oxc)
Also is says: Service uuid XXXXXXX not found!
...
The nRF52 SDK ANT example "ant_scan_and_forward/" configures a device linit of (16-1)=15 in this line:
// Public Definitions #define MAX_DEVICES ((uint8_t) 16) /**< Maximum...
On nrf52832 and nRF5 Mesh1.0.0
When running idle state(not RX/TX), current comsumption is over 400uA.
And every 100ms, CPU is wake up.(small working.)
What happen...
Hello! I am using application that support ANT+ and BLE, so i am using s332 softdevice. now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v13.0.0-1...
Hello.
Which application can I use to monitor and configure a smart wristband with nRF52832? I would like to check its firmware, update it and see all the info about the...
Hello. I've got issue with TWI and power down mode. I modificated "ble_app_bps" example, prepared own service and characteristic and I added BME280 sensor. And almost everything...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
Hi,
I am trying to alter ANT/BLE relay example to work with multiple ANT+ channels (HRM and BSC), but the program resets after ant_xxx_disp_init() step for the second...
Hello,
I would like to use app timer based on RTC1 in order to wake up the MCU every X sec. The app timer seems to work correctly when the MCU is working. I use the following...
Hi everyone,
We are developing with Nrf52 and it's been a bit of a manual process for us to test our code, we use makefile so we were able to create a clunky system to...
