Hi All, I have a question regarding modem DECT phy API. There is a function nrf_modem_dect_phy_event_handler_set(nrf_modem_dect_phy_event_handler_t handler). I'd like to know...
hi,
im using nrf5340 controller (central) to get measurement reading from multiple medical instruments (peripheral) simultaneously. everything work as expected. however...
I want to have two Kconfig flags that are both booleans but the build will fail if both are set. My code below used to work in pre ncs3.0, I'm wondering if there's a better...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
Hi,
I use the UART to do the device firmware update and have used the dfu_dual_bank_hcl to compile.I use the nRFgo Studio V1.16
to program the s110_nrf51822_5.2.1_softdevice...
I've downloaded the latest SDK and soft device. I've been able to compile the ble_app_ancs project, run it on my dev board and even connect to my iPhone. Although I'm getting...
Hi everyone
I'm using the nrf51822 connect with stm32f103 through UART,it's current is >1.9mA,is it normal?
I have full reset to disable the debug interface,it can...
Hello developers,
I've got an nrf51822 EVA kit with on it the QFAACA chip. KEIL v5.0.5, J-link V4.78, nRFGo Studio V1.16 and nrfGo SDK (zip) V4.4.2. The Softdevice on the...
when I enter the system off mode then used a GPIO to wake up the IC, the "RESETREAS" register show "Reset due to wake-up from OFF mode when wakeup is triggered from the
DETECT...
Hi,
I have only nRF51822 DK without starter kit motherboard. how can I download softdevice(S110 Bluetooth low energy stack) to my nRF51822 chip in the Keil environment?
...
Hi all,
the release note of SDK 4.3.0 reports that it was tested and verified using BLE S110 version 5.2
When it will be available (version 5.2) ?
Actually we can download...
Hi,
I want to read the data by the radio.now I have read the temperate data from the tags by 51822. the data include the ID value and the temperate value. the ID is hex ...
Hello,
I'm working with nrf51822 on a custom board and i'd like to use the LPCOMP as wakeup source. I configured the module by the code listed above:
void lpcomp_init...
So now that I understand the problem with overlapping asserted events on the GPIO port, I can't figure out the correct way to reset the sense field in the GPIOTE_IRQHandler...
Hi,
I follow steps in User Guide version 1.2. The Blinky project is working fine.
Then I program SoftDevice and after than compile and Download HRM using Kail
But led...
now,i pairing my peripheral and Communication read/write data. but have some issue for disconnect/reconnect .
1.disconnect: when i disconnect (call didDisconnectPeripheral...
Hi,
We are using Nrf51822 , pca1001 evaluation board.
when i flash bel_app_proximity code (by disabling led function in advertisement_star()),
current consumed by...
Hello Developers,
Just started with the nrf51822 and managed to install:Keil 5.05, Segger J-link, nRFgo Studio 1.16 and the Master Control panel. I also loaded the SoftDevice...
Hi,
I'm knowing the device_firmware_updates project in SDK and I want to know whether I need to program the softdevice when I do the device firmware updates over UART?...
