Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi Sir/ Miss:
I've a custom peripheral heart rate device.
I use central example "ble_app_hrs_c" to connect it by PCA10040.
After I set up the service (Target_UUID) and...
Dears,
I'd like to add service while connection.
Now I am using UART service and want to add HID service when I put button.
How to add HID service while connection...
I am using Master Control Panel for doing DFU on nRF52832 DK. The nRF52832 is having example dfu code dfu_test_softdevice_w_bootloader_b_s132.hex from sdk11.
nRF51 dongle...
Dear experts,
I'm a new user of NRF52 technology and I use:
Keil µVision v5
NRF52832 (PCA10040)
Keil software pack 8.15 from Nordic Semi
debugger Cyclone...
Hi Nordic
I am porting an application from the EM9304 SoC to the nRF52810.
In the old application it was possible to send 26 bytes of manufacturer specific data (plus...
Hi,
I use BMD-350 on NRF52832 with SDK v13.0.0
I configure my radio to run the BLE at -20dBm power through the API sd_ble_gap_tx_power_set()
But few seconds after starting...
Hi!
I once set up a simple project using SDK 12 and the HRS example.
Now I tried porting it to SDK 14 and SD 5. That didn't work out well.
So I started things from...
Hello everyone,
I am working with TWI and broadcasting of data using ble_app_beacon. I am facing a problem in broadcasting of the data. I have complied the code and it runs...
Hello everyone,
I am working with TWI and broadcasting of data using ble_app_beacon. I am facing a problem in broadcasting of the data. I have complied the code and it runs...
Hello, Nordic.
I use NRF51822. I know NRF52 series is able to NFC Tag with Antenna.
But I want to use NFC module with NRF51822. If I can modify NRF51822 circuit, is...
Hi DevZone,
I am doing my project base on SDK 14.2.0 example spi. I modified the PIN according to Arduino PIN map and connected the nRF52480 Preview DK with Arduino Uno...
Hi Everyone,
So I have a custom board with an LED on P0.9. I have confirmed it works by applying power to it, so no issue with the LED itself or the way it is connected...
Hi,
My problem that the RAM is insufficient for my project.
Please, I want to know how to set optimization configuration. By the way, my central device only connect our...
Hi,
I was trying some examples of the SDK 13 and 14 for keil but now I need to undestand how works the ble mesh.
I did the download of the SDK mesh, and there are only...
