How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
The nRF52 SDK ANT example "ant_scan_and_forward/" configures a device linit of (16-1)=15 in this line:
// Public Definitions #define MAX_DEVICES ((uint8_t) 16) /**< Maximum...
On nrf52832 and nRF5 Mesh1.0.0
When running idle state(not RX/TX), current comsumption is over 400uA.
And every 100ms, CPU is wake up.(small working.)
What happen...
Hello! I am using application that support ANT+ and BLE, so i am using s332 softdevice. now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v13.0.0-1...
Hello.
Which application can I use to monitor and configure a smart wristband with nRF52832? I would like to check its firmware, update it and see all the info about the...
Hello. I've got issue with TWI and power down mode. I modificated "ble_app_bps" example, prepared own service and characteristic and I added BME280 sensor. And almost everything...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
Hi,
I am trying to alter ANT/BLE relay example to work with multiple ANT+ channels (HRM and BSC), but the program resets after ant_xxx_disp_init() step for the second...
Hello,
I would like to use app timer based on RTC1 in order to wake up the MCU every X sec. The app timer seems to work correctly when the MCU is working. I use the following...
Hi everyone,
We are developing with Nrf52 and it's been a bit of a manual process for us to test our code, we use makefile so we were able to create a clunky system to...
I might need to use SPI and I2C simultaneously in a design, due to the fact that one of the components is only available in an I2C version.
Can the nRF52840 be configured...
Hi
We exposed NFC Type 2 functionality in our nrf52 a while back. Then the NFC SDK got refactored and I had to refactor my code to suite.
Now I am trying to enhance my...
Hi,
We would like to protect our product from people accessing the device via J-Link. We build our application with FreeRTOS. Can we follow this to set it before I start...
Hello,
I want to change data channels after provisioning, I follow devzone.nordicsemi.com/.../ here.
To set,
memset(&new_opt_config, 0, sizeof(new_opt_config));...
