Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I'm building wih Keil MDK-Lite Version 5.24.1 and I just copied the examples for gpiote into my own folder, everything was kept the same (ie copying from C:\Nordic\nRF5_SDK_14...
Hello. I tried to use UART speed 115200. But my slave does not response. I connected slave to the arduino and it is working corectly. I got 2 oscillograms . From arduino and...
Hello everyone,
Currently I'm altering the "ble_app_uart" and "ble_app_uart_c" examples (both under examples/ble_peripheral) to suit my needs. What I currently need to...
Hello,
I have interfaced one sensor with pca10040. I am using sdk 12.2.2. I am sending the data from sensor in advertisement packet(manuf specific data). Now my sensor data...
after the advertising timeout occurs the board goes into sleep mode and then immediately runs from the top of the main function. I know that a pin state change can wake up...
Edit: Rephrased the question to make it easier to answer.
I used flash storage to store a couple of variables between resets in a app made from SDK 12.2, now I am attempting...
hi,
i need to reconfigure the WDT and also change the timer value in WDT. is it possible to do that.
i tried but i can not.
1.configured wdt with timer 5sec.
2.i...
Hi guys,
we are developing firmware for nrf52832 SoC based on the mbed platform.
The firmware uses BLE and few peripherals (timers and pwms). Since our goal is to build...
Is it possible to scan and make Gatt Connection simulataneously from Android app to NRF device.I have seen issues in second connection after disconnection.I have seen second...
Question for I2S.
Execute follow.
[TXD.PTR set A] 1st
[START]
[TXPTRUPD event] (not set TXD.PTR) 2nd.
2nd transfer address use A?
How long time between...
There are a few setting options I would like to keep through power cycle like sensor sampling rate, continuous sampling on/off, etc. I had success implementing saving of one...
I'm using a PCA10056 (NRF52840 Preview DK) v0.9.1, and trying to erase the existing firmware, but running into issues.
I've tried nrfjprog -f NRF52 --eraseall with version...
Hi
I am running some thing similar to the multiprotocol ble_app_gzll example but using freeRTOS and peer manager. Effectively the the main in ble_app_gzll example is a...
In my test, light_control example consumes about 17mA, same for both of client and server.
I'm using nRF52DK, PCA10040, and SDK is "nrf5_SDK_for_Mesh_v0.9.2-Alpha".
I...
Hi,
I am using SDK 12.02 with softdevice 130 and having a odd issue here.
In my application, I want to advertise ADC value via beacon and to report the ADC...
