I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hi,When I use nRF Connect app(IOS version) to connect my ble device,BLE_GATTS_EVT_SYS_ATTR_MISSING log information appears in my RTT Viewer(Picture IOS_Phone_Conncet).After...
Hello,
I tried as you mentioned using sdk12.1.0 buttonless_dfu and bootloader_secure example.
I didn’t modify anything except dfu_public_key.c.
As shown in the attached...
Hello,
I have a program that do an infinite loop in sd_softdevice_enable. How can i investigate ?
Loop is from 0x00009DEA to 0x00009DF2
Target is nRF52832 AA with...
Hi,
I am working on nRF52 with freertos + SDK13.0 + sd S132_4.0.2. I found the device will be trap in the xTaskIncrementTick of the xPortSysTickHandler when some task is...
Hi Nordic, can you please confirm the device ID for nRF51822 QFAA G1?
The HWID I discovered is 0x004A
Pls confirm so I can pull an update request for Black Magic Probe...
I tried to run the ble_app_hrs_freertos example on the pca10040 devkit, but it's not possible to connect via ble (using nrf connect, neither with pc nor with smartphone)....
Hello,
I'm testing the capability of BT5 so I bought two nRF52840 Preview DK (I also have one nRF52832 DK) and I have some questions that may speed up the work.
...
Hello,
i am writing an application which uses the SDK13 peer manager library for bonding. The Nordic chip is acting as a peripheral.
Is there an easy way to prevent...
Hi，I update my IAR IDE from version 7.70.1 to 8.11.1，when I compile the workspace ble_app_hrs_freertos_pca10040, the error occur in port.c, as following:
Error[Og014]:...
First try to create a TWIM driver from scratch without any DMA. Following the steps in the OPS I get mixed behavior and only the chapter with DMA generates any clock and data...
I ran into an odd issue on nRF52840 using s140 version 5.0.0-3.alpha. My application erases and writes to a region of flash.
I've found that I'm able to erase the pages...
Hello,
I have implemented experimental DFU buttonless example with my application and able to do the firmware OTA via secure bootloader example using private and public...
Hi,
I'm experimenting with the nrf52840 preview board.
I have tried the example "ble_app_att_mtu_throughput" using the coded option to check the extended range and it...
hi, everyone!
I have a question for pstorage, when i use pstorage_store,it was failed, return error code :15 how to solve it. Below is my code
void custom_flash_init...
With good luck, I traced my connection timeout to the slave/peripheral using nrfSniffer. What is most unusual is the slave unexpectedly stops corresponding with the master...
