Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Devzone,
I've been working on a central device based on the project 'ble_app_multilink_central' and have encountered an error originating from within the softdevice of...
In Bluetooth 4.1 spec they mentioned scatternet option for BR/EDR topology....not for LE topology...
is that option of connecting to multiple centrals at a time will applicable...
I need a BLE device that can broadcast codes/id to my android mobile app. Also, I need those codes be changed by once in a while by an admin app. Is this possible?
I'm unable to get any output when writing to the UART while using the s110 softdevice. I'm refering to the hardware UART. I'm not using bluetooth for serial.
I'm using...
Hello,
I wrote a firmware for my project, based on the UART over BLE example, so using the softdevice, establishing connections, etc. It works.
I'd now like to use a...
Hi all,
I can program and debug my application just fine when the softdevice is not used (initialized). Problem is, when I do use the softdevice, I end up in Hard Fauld...
Hello,
In our prototype (Embedded System) we want to use nRTF24AP2 with Chip Antenna, as W3006, for example.
Our questions are: where and how needs to be placed the Chip...
Hi there,
I currently have an nRF51 DK set up transmitting six 20 byte packets per 7.5ms, there about, to an nRF51 Dongle set up as a central. When viewing with Master...
Hello,
I would like to move on from using nrf_delay_ms().
I thought this would give me some first results, but It don't. Whats wrong?
//a
static void test_timer_handler...
Should be noted that i'm using nRF51822 breakout board and i have a lot of problems with its programming. And i'd just begun to write own topic about my problems with connection...
Hi,
I am playing around with the BLE_proximity_template on the Redbearlab BLE shield and an Arduino Uno. I uploaded the sketch and paired my Android Lollipop device with...
I'm a beginner and have been using library provided by the nordic to communcate with nrf8001. I read nrf8001 data sheet but couldn't understand how to use the aci commands...
Hi,
I want to get this dongle to 'see' the data being transmitted to and from the nrf51 dk. I saw a note here adafruit saying
The sniffer firmware cannot be used...
Hi,
i wuold like to control one port of my home gate's centraline by Ble shield on Arduino.
I need to send an impulse for 1'', no more. Like a release button, not like a...
Got it working .. forgot (didn't know) I had to change the attribute length as well
I am currently trying to figure out where/how to attach my measurements so they can...
