Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I am using NRF51 DK and I would like to try using the custom service so I download the nrf51-ble-app-lbs from github.
github.com/.../nrf51-ble-app-lbs
It stated that...
Hi,
I'm using nRF51822 Development Kit and trying to program softdevice with nRFgo Studio. The file to program is C:/Program Files (x86)/Nordic Semiconductor/nRFgo Studio...
developer.nordicsemi.com/.../a00969.html
I'm trying to understand whether this can be called in a timer interrupt ( app_timer ) and how frequently. I seem to have a bug...
I have nRF51822(pca10005), Dongle(pca10000)
And DownLoad Keil, nRF Tools, nRF Studio, nRF SDK, Sniffer, wireshark.
I try to run the example
C:\Keil\ARM\Device...
I am debugging the bootloader to work with a custom board. I have the bootloader project open, no application programmed, s110 softdevice programmed, and the hexfile for the...
I want to use app(nrf uart 2.0)
so, I try to change UUID,
but I don't know how make custom uuid and use it
and I don't find function(ble_cs_init())
hlep me, p...
I just tried compiling this for the BLE nano and it explodes to a 245K download (much too large for device). I've also tried including only the headers (DigitalOut and wait...
Hi,
I purchased Nordic new reference platform nRF51-DK(pca10028) and try to work for DFU OTA.
In my test, first of all program S110 V7.1.0 by nRFgoStudio and downloads bootloader...
Hi
In a bit of an over-enthousiastic mood, I bought 3 pieces of the nrf51822 beacon kit, and the, as this did not gave me download access to the NRF51 SDK, bought a nRF51...
Is there an example of using sd_ble_gattc_write() to do a long write?
I'm assuming I need to use BLE_GATT_OP_PREP_WRITE_REQ and
BLE_GATT_OP_EXEC_WRITE_REQ.
devzone...
Hello everyone,
I am using the Softdevice s110_nrf51822_7.1.0_softdevice.hex and the dfu_dual_bank_ble_pca10028 example with SDK 7.1. I am trying to achieve a Device Firmware...
I am using Android Studio and am developing a system with the nRF51822. I would like to use the available sample code - nRF Master Control Panel APK for Adroid - available...
I'm wondering about the best way to implement a bonding and also a non-bonding device. There are a lot of code parts in the SDK that show a way of implementing a BLE peripherial...
