I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
We are designing product based on nrf2401A
The problem that we encountered was that the nrf2401A forgeted configuration data, was it possible ?
we use our product in highly...
Hi,
I am using the nrf51822 in an intermittent high-current application where if the battery is close to dead, will sometimes cause the chip to reset because the voltage...
I am using SDK 8.1.0 and Eclipse on a Mac. I am having difficulty flashing my app that uses the nRF51 sdk onto nRF51. I am using JLink
I assume I need to flash two things...
Hi nrf51 developers,
I'm developing multiprotocol application by combining BLE and a proprietary protocol. I'm using concurrent multiprotocol timeslots API. Started with...
I am new to programming both the nRF518122 as well as the Cortex-m0. As I have been building and running the example apps that come with the nrf51 sdk, I run across the CMSIS...
Hello,
I'm developing device application where I need:
peripheral (advertising also when in connection)
central role
whitelisted connections
maybe some encryption...
Hello,
I'm trying to do some simple printfs to hyerperterminal as a way to debug my code. I have used the uart example init code but nothing prints:
void init_uart(void...
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I have a nRF51DK. The Softdevice on the board is S110.
I load the ble_app_template from the SDK 8.1 on the chip. It builds with success. Now with the MCP I am able to see...
I'm now using the lastest SDK 8.1.
I found that if I call app_button_enable() after app_button_disable(), app_button_enable() would not function again.
But if I changed...
Hi all,
I read that the nRF51822 comes as a blank chip from the factory, and this means that we have to program the SoftDevice ourself. I am wondering if this is the only...
Hi,
I'm using the Rigado BMD-200 Eval Board with sdk 8.1 and am running the ble_peripheral example titled ble_app_uart. I am using my iphone and the nRF UART app to communicate...
If using the button handling library the #define GPIOTE_CONFIG_NUM_LOW_POWER_EVENTS needs to be changed to add number of buttons being handled.
This wasn't clear to me...
Hi,all. i want to set tx power use interface "ble_tps_tx_power_level_set",and read back tx power level used tps servoce on my phone.how to do that ?Thanks for your reply!