Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
I am trying to create a file and write to it during runtime. When I use fopen with "w" option to create a new file, the file pointer is always retuned to be NULL.
Is there...
Hi,
I recently tried SDK7.2 on PCA10028 board in order to make sure that SDK7.2 works well before I migrate my project to SDK7.2 codebase. My project code didn't work as...
Is it possible to do OTA from one nRF51822 to another? Is so how, and is not why?
I am using S120 and S130 for my applications and would like one device to uppgrade another...
Nordic has provided a good SPP implementation over BLE.
devzone.nordicsemi.com/.../
However, will it raise power consumption and cause BLE to lose its low-power characteristics...
When trying to do a direct advertise massage ( sd_ble_gap_adv_start ) I get error code NRF_ERROR_INVALID_STATE (Invalid state, operation disallowed in this state). This is...
Hi Team,
In my application UART is used.
I need to send parity bit based on particular responses that I need to send to the device
connected to UART.
Can I change configuration...
Hello,
I'm working with timeslot API (basing on github.com/.../observer) . I have an advertising and active scanning running concurrently. However, I want to completly...
I am using nRF51822 to generate 3K HZ PWM signal for a buzzer.
I read other people's question and try it.But as far i can't solve this issue.Please help.
At first i use...
Hello,
I just ordered a shiny new nRF Beacon from Mouser. The beacon is version 1.1.0 advertising "DfuTarg", so I am attempting to flash the application file that comes...
Enlight of the increase in 8.0 SD size, I am concerned that my application size may soon grow too large to utilize Dual Bank DFU. I know the actual size of the .Hex files...
修改Device_Name.jpg
After programming, the device name cannot be changed.
Is there any solution that can achieve?
I know that I can change the paramter from the function...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
The Master Control Panel will be able to keep the connection for hours and hours.
But when I am using the iPhone 6 to do the test, after connected, it will also be disconnected...
Hello
I've been having some strange problems with my SPI and TWI bus. In my setup, I'm using SPI0 and TWI1. I noticed that, even though I'm not using it, that SPI1 was...
