I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am attempting to connect and send data between an nRF51422 (DK) running the UART Peripheral Example Code and an nRF52832 (DK) running the UART Central example. I am able...
We are a medical company utilizing the NRF51822 board with SDK 11 for our application. As part of filing for approval for our product from the FDA we are required to prove...
There is a corner case in pstorage_raw.c that can cause a deadlock between pstorage module and the pstorage system event handler. This in turn will cause all the future pstorage...
Hi,
I just implemented LESC Numeric Match on the NUS service for my peripheral device (based on ble_app_multirole_lesc example). I am able to connect to my device using...
I am using the esb_tx example on an nRF51 DK board modified to send BLE advertising packets at 1 KHz.
I am receiving the packets on a BlueTooth sniffer. The contents of...
Hi,
i'm designing a board based on NRF51822-QFAC chip and i'm using this antenna chip 2450AT43A100E and this balun 2450BM14E0003T .
I put the balun as close as possible...
I have __asm("BKPT #0\n") in my code. When running without a debugger, it seems to generate a hard fault exception (which I can tell because I have a hard fault handler that...
This week I worked myself to a series of what seemed to be problems boiling down to one issue:
The Notification Write Response is lost when bonding has to happen first. ...
I'm trying to save power on my HID keyboard application by disconnecting the Bluetooth link after some time of inactivity. As soon as there are keystrokes to send, the device...
The question has been answered before, but the answer references a document called nAN-29 at this link: www.nordicsemi.com/.../73843444 . Which doesn't seem to be working...
Hello,
We use the PCA00031 dongle running the MEFW 0.9.0 in our production environment to validate a sensors accuracy. The PCA is controlled by a C# test program using...
Could someone explain the pin numbering scheme in regard to the interrupt setup handler?
To be specific, what pin number should be passed to nrf_drv_gpiote_in_init for...
In the ble_app_att_mtu_throughput example for the PCA10056 I am getting a "fatal error in the include chain" pointed from the #include "amt.h" line in amts.c. Specifically...
Hi,
I'm working on a firmware that is used in a nrf51822. I discovered an unwanted behavior of my system.
When the system is in power_manage mode, it can wake up in two...
● device : nRF52832
● sdk : 13.0.0
● softdevice : 4.0.2
Hi,
I have a problem with change mtu size.
I changed mtu size in sdk_config.h, but android application can't read...
