Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello
I have written some code to write the nrf51822 via SWD. It all works, but I would like to make it faster.
I am currently writing one word at a time. If I read...
Hello dear friends,
I'm trying to bring up a Raytac module for the first time. I was able to program S110 7.1 and I'm using the Beacon example found in the SDK 6.1
But...
Is there a similar way tot get the radio's MAC address when using Gazell only (no BLE)?
In SoftDevice there is a "sd_ble_gap_address_get()" function call.
Hello All,
I'm trying to program a NRF51822 module for the first time. I'm using the Jlink for ARM from IAR which is segger rebranded. It supports JTAG and SWD.
We got...
Hi,
I am trying to obtain a 10khz PWM (50%) on an output using Timer2 (see code below). It is working fine up to around 500Hz (2msec), above that (1kHz) I am getting only...
I would like to develop an application with nRF8001 DevKit. The master emulator of this kit is an USB Dongle and it is originally meant for PC connection. My final goal for...
Hi all,
Problem: Second harmonic with nrf905.
I used nRF905 and exact recommended design&layout in the datasheet. Now, it is said that there are 2. order harmonics ...
It seems that the all the msc_inline_*.png files are missing from the SDK 6.1.0 documentation directory.
For example:
file:///C:/Nordic%20Semiconductor/nRF51%20SDK_v6...
Hi,
I use NRF51822 as a transmitter in "gazelle mode" so no soft-device is enabled. At the other end I use NRF24LE01 as a receiver. In order to see what is going on in...
Hi All.
I made a nRF51822 based PCB with SWD header but I don't have any J-Link lite to load Firmware.
I have a nRF51822 Eval Kit. Is there any way to use the J-Link of...
Hi,
I am using nRF51822 and I compiled and loaded uart example code. Also i used nRF toolbox android application on samsung s5 with android 4.4.2.I am using sofdevice 6...
Hi All,
I would like to broadcast 256 byte data in one shot every second, any reference in SDK recommend?
Thanks in advance.
**updated at 19 Sep, 2014
Application...
Nordic,
After upgrading to S110 7.0.0 the BLE_LBS example no longer works as downloaded from GitHub. I adjusted the flash algorithm size which fixed the first problem and...
