After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi
during setup of a peripheral at startup, I need to add some wait periods in between steps of the setup. Is there some function like waitMS(int time) or something, that...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Folks,
Newbie here with mbed, using nRF51-DK, but old hand with nRF51822, S110, SDK, J-Link, Keil MDK, etc. Trying to figure out how the mbed SDK API maps down onto the...
I have 25Q64 SPI flash chip connected to SPI bus. Unfortunately it works too slow even with using IRQ routine via SPI0_TWI0_IRQHandler (everything done like in example spi_master...
I was wondering if its possible to do a "Create new user" function, so the new bonded devices are accepted only if the first connected master tells the peripheral to.
For...
Hello,
I have taken the ble_app_beacon example and added a few things... I am looking to do something very simple like light up an LED on connection. So i added the on_ble_evt...
When is the S130 going from alpha to beta or release?
I understand that what ever answer is subject to change...just hoping to get a "ball park" date/plan.
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hi,
I am using NRF51822 BLE. I wanted to know that when we put this BLE ic in sleep mode then, is there VDD_PA voltage is still 1.6V or it becomes shut off internally.??...
Is it possible to generate useful documentation from the provided .dox file ?
If I run doxygen.exe ble_api.dox I get some Latex and HTML output but looks incomplete because...
What would be the best way to go about sampling and transmitting a signal at 60 Hz? I am considering setting up notifications and a characteristic, but I don't think that...
Mac OS X 10.10 Yosemite rejects the format of the file system and puts it in a read only mode.
This issue was raised last October 24, 2014 at https://github.com/mbedmicro...
Hey guys,
Sorry to a basic question here, but it's been a few hours and I still can't get a connection to either of two brand new nRF51 dev boards, trying both on WindowsXP...
Hi Sir,
I’m working in an application with the demo board A to communicate via Bluetooth to the demo board B and send data between them. In the module I have to do send a...
I have a 51822-DK board. I have followed all of the instructions to set up the environment. Loaded all NRF tools, Keil v 5, install SDK. I began working on the examples. I...
