Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I am new to Nordic and am using SES as my development environment along with the Nordic SDK v15.0.0. I have followed the instructions for installing the CMSIS configuration...
Hi,
i am using light_switch example in nrf5_SDK_for_Mesh_v2.0.1_src with nRF5_SDK_15.0.0_a53641a . Here i flashed proxy_client and proxy_server onto two different NRF52832...
nRF5_SDK_11.0.0_89a8197 - with MPU.7z this is how my nRF go studio looks with example blinky and works well.
nRF5_SDK_11.0.0_89a8197 - Copy.7z I am trying to wire NRF 51822...
I have found out some data about flash:
Flash memory Endurance 10 000 Write/erase cycles
My question is UICR's life is same ?
If use ERASEUICR will erase all area (eg...
Hi everyone,
Days ago, I met a problem while trying to implement the DFU function with MESH SDK 2.0.1 and nRF5_SDK_15.0.0 following the quick start guide on different systems...
Hi,
I received my nrf52840 Dongle today. It works quite well using nrfConnect.
However, we need to implement our custom USB bootloader since the default USB bootloader...
Hi,
Since I saw nrf52840 is for "mouse, keyboard" in document, may I ask, is there any hardware supporting to read mouse PS/2 protocol?
If there isn't, any idea to read...
I have an in memory log, built using a custom log backend, which I write to using the NRF_LOG_*() macros.
My implementation of app_error_fault_handler() will do some NRF_LOG_ERROR...
Developing with S112 + Emulated NRF52810 I've run into a road block.
I've set `m_adv_uuids` to the following:
static ble_uuid_t m_adv_uuids[] = { {BLE_UUID_DEVICE_INFORMATION_SERVICE...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52.
I am using MPU9250 and nrf52840 pdk.
I've managed to set up the DMP and...
Hello - I have looked through documentation and can't confirm which component on the board is the BLE Module. Could someone follow up with an image of the board to help confirm...
Hi, we are looking at using a FCC pre-certified nRF52832 module such as the murata MBN52832. It would be for a wrist mounted product so will be in close proximity to the body...
Hi there Nordic Semi/ forum,
This is actually my first post here.
I got the NRF52 DK and I want to implement the NFC type 2 ( passive) tag with it that I could both read...
Hi, I am trying to use P0.9(nfc pin) as gpio(input) to read the charging status of a battery from battery charger IC(BQ 24230). the Open-Drain Charging Status Indication of...
