Hello,
I am trying to modify peripheral_hids_keyboard 's security configuration as Security Mode 1 Level 2.
According to some Q&A thread, I tried the following:
1...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Dear Sir.
I have a question regarding the nRF9160 Interrupt procedure.
I have 2 interrupts on my nRF9160 custom board.
The 1st interrupt is an external interrupt every...
I'm using nrf52840 DK board with modified program of light switch example from sdk 2.1.1. While provisioning with interactive pyaci i'm giving provision address maually to...
Hi dear Nordic Team
I'am currently implementing a 802.15.4 compliant ShockBurst Radio TX/RX module on the NRF52811. As far as I understand there is a crc 16 implemented...
Dear All I had gone through nRFGO Studio for custom UUID But how to generate the Hex bytes so that i can put as in code for having custom service as shown below for above...
Hi community ! I'm testing Mesh characteristics by using debugger. Currently, i send messages through nodes and waiting for acknowledge, and I put a timer to get latency....
Hi,
present i am using nRF52840-DK for to develop the BLE application. here i am facing the debugging issue.
i.e. in my board i programmed S140 soft device. so after that...
Hi,
I am trying to read serial data via UART_1 with v1.2.0 SDK. According to dts-File UART_1 is configured with pin 0 and 1 on the devKit.
I added
CONFIG_SERIAL=y CONFIG_UART_INTERRUPT_DRIVEN...
Hi,
All was working on SDK 1.0. Now I have SDK 1.1 and new Segger and new nRF Connect and gnuarmbemb (I had a new computer, so did set up everything from scratch)
...
Hi,
I´m trying to work with the "TWI Scanner" example, provided by SDK 16. I Use nRF52833 DK (PCA10010), unfortunaly there is no solution for PCA 10010 in the SDK. This...
Which function is called nrf52832? When do I click the "enable CCCDs” function on the NRF Connect App, and which variables are the nrf52832 data set?
Step 1: Connect
...
Looking for help creating an example similar to the usbd_msc example that works with the W25N01GV . Currently using SDK 15.0. Would like to see this work with FatFS or possibly...
Hello, the NFC used in our product has two major application
1. read/update configuration data by using the external smart device through NFC TAG here I am setting up type...
Hi everyone,
I'm currently working on my bachelor thesis and need some LOG ouput from my application. I'm using the Development Board from Makerdiary and the nRF5_SDK_for_Thread_and_Zigbee_v1...
