Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi,
I am using the Power Profiler Kit (Rev. 1.1.1.) with Power Profiler app (v2.3.1) to measure power consumption on an external DUT. The issue I am facing is negative current...
Hi all,
We have designed a PCB where we use BMD-350 ( which is based on nrf52832 ) , HX711 and the accelerometer ( MMA8452Q ) as primary components. The device is supposed...
I am in the process of integrating the latest SAADC driver into my project and have noticed an issue after adding the errata 122 workaround to my saadc event handler per the...
Thanks in advanced. On sdk17.0.2 examples\ble_central\ble_app_uart_c, I connect a button's one end to nrf52832 pin 24, the other end is connected to VDD. So I have to #define...
Hi,
There is an option CONFIG_LTE_NETWORK_TIMEOUT for the LTE Link Control. The default is 600 seconds (10 minutes) but I couldn't find any suggestions for the timeout and...
Hello ,
Now I am sending the data per 7.5ms in the interval of time over ble .I am loosing the packets , to avoid this I am planning to send the data in the structure .How...
Hi,
I got a unit based on NRF52 (No matter what SDK) which is connected via 1-wire (dallas protocol which is very time accurate) to other unit.
The other unit is the master...
Hi! I wanted to ask someone who knows more than I, if this setup makes sense, and how I could test my design.
A bit of background: We're developing a custom board which...
Hello, I am using nrf51822 / SDK 12.3 / SD 130-2.0.1.
When a normal timer is set and softdevice off, the timer interrupt does not occur.
In SDK 10 / SD 110-8.0.0, timer...
Hello,
I am trying to use the flash API of fstorage in my code. I have called below function at the start of my code. I want to save some integer values every 1 min interval...
Hello
I am trying to read a characteristics from my peripheral using my central. From what I read here, I have to use sd_ble_gattc_read(). Is it correct ? But I did not...
Hello
We have produced boards with a Telit module using the nRF52832 chip.
Our software developper have a lot of problems making the connexion and communication reliable...
Hello,
After a long war trying to connect MPU6050/MPU9250 to NRF52 DK with nrf52832 on board, I finally succeeded and I am getting values through UART.
But I have 3 problems...
Hi,
I would like to get the stored CCCD values of a bonded peer using pm_peer_data_load()
I am currently struggling with the format of the data returned by pm_peer_data_load...
