I'm trying to get NFC power-up/restart working on nrf54lDK but the call to sys_poweroff() results in: E: ***** BUS FAULT ***** E: Precise data bus error E: BFAR Address: 0x0...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
There is an error in projects that utilise RTT for CLI. SDK_CONFIG.H contains the line CLI_RTT_ENABLE. This must be CLI_RTT_ENABLED for the macro NRF_MODULE_ENABLED(CLI_RTT...
I go into MCUBoot mode and I get: MCUboot DFU failed. Error occured when program. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: Unknown value (ffffff8e) When trying...
Hi all,
I'm evaluating design for a bluetooth + GPS + NB-IoT ultra-low power device
I see the only possibility to get a such module is to design it (I didn't found anything...
Hello,
I'm trying to auto-build my application through Github actions however I'm running into this problem
When I try to run this locally it works perfectly fine however...
Dear All, I am trying to measure the current consumption for an application I am developing on the nRF52833 DK. The code that I am running is the following: Based on the product...
Dear All, I would like to configure a device to go to the System ON, no RAM retention, wake on RTC (running from LFRC clock) Sleep mode, in order to be able to use the RTC...
Hello,
we are using nrf5 SDK version is 17.0.2 and nrf52840.
Our product uses nrf52840 and its USB capabilities being configured as a composite device (HID keyboard +...
Hi,
i would like to know which software i have to download and install, so that i can program a really basic function like pressing the button and turning on and off an...
Hi,
I saw a Linkedin post by Zephyr where they mentioned some Vscode extensions for devicetree and kconfig:
https://marketplace.visualstudio.com/items?itemName=trond...
Hi,
unfortunatally i could not add a new LTE device. I was able to activate my SIM card but not able to finally add the device to my account.
The error code is: There...
I am currently following the tutorial for creating custom services ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ). The only differences to this...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project. I need to work with another chip through SPI. This chip is the master and...
Hello,
I have one more questions while doing test with SAADC, UART.
When I was tested the SAADC pin connect with ground, the negative value occurs.
So, I changed the...
Hello,
i've built a basic Thread network with two nRF52840 Nodes running the CLI example and a RasPi with a nRF52840 RCP as BorderRouter.
My Question is:
Whats the...
