Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
I am having a high rate of connection reason 0x3E when connecting two nrf52832 devices together both with only one active connection at a time.
Most of the information I...
hi..
development board - nRF52832
SDK version -15.2 version
Fellowed method - B1b. Use Oberon crypto library instead of uECC
softdevice version - v 6.1.0
tools using...
After pressing F5 I get.
Preparing target for download Executing Reset script TargetInterface.resetAndStop() Reset: Halt core after reset via DEMCR.VC_CORERESET. Reset...
Hi,
I'm using NRF52811 to evaluate the direction finding. I have successfully got the phase data, but I found a strange thing:
I did some processing on phase data for...
I am currently testing Optiga Trust X using an NRF52 DK. I am using armgcc as my toolchain.
The example provided by the nRF5 SDK v17.0.0 is a great starting point and I...
Hi,
I am using nrf52810 and a sample SAADC code from the examples folder provided by the manufacturer. I have connected a potentiometer for validating my output values....
A continuation from here: https://devzone.nordicsemi.com/f/nordic-q-a/64842/mesh-pa-lna-problems
If I want to only enable the PA/LNA chip for the mesh stack, but not for...
Dear Nordic Support,
Our product is based on nrf52840/s140 and we have difficulties connecting to it using Huawei P8 Lite while it is fine using other Android or iOS phones...
I have a compiled code and I want only to change the uart pins without compiling the code again
If it is possible to modify only the hex code, how can I find the UART pins...
I am trying to find where to submit bugs against the pc-ble-driver. There are two major bugs I have found
saved CCCDs (in a bonded connection) do not get restored when...
Hello, everyone
I use NRF52840 to configure TWI to operate the sensor, but I don’t understand it.
Can the hardware TWI of 52840 be mapped to any IO?
Or is there a fixed...
Hello!
NRF52832 is used as a central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
On android phones...
when I use usb to transfer, i fine many datas are lost.Is it because the DMA size is too small?Where can i see the dma size?(In nrf52833/examples/peripheral/usb_cdc_acm )...
I am trying to connect a SPI device to the external connector pins on the nRF9160dk board. I believe I know the name of the SPI device and the pin connections from the device...
