I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
In the Buttons and LEDs page, the LEDs are connected to P0.28-31 but in the connector interface page, the Figure 1 show LEDs connected to P0.13-16.
Buttons pins also looks...
Hello,
I am trying to create an application on my nRF52-DK using several custom service peripherals, each with 2+ characteristics. I have completed a few tutorials on...
Hi,
I am using USB device CDC, and the COM Port name on the PC is "nRF52 USB CDC BLE Demo (COMX), see the picture below.
How I can change it ? can I change it from...
Hi,
I followed the instructions described on https://github.com/NordicSemiconductor/pc-nrfconnect-launcher but I cannot "Start scan" within nRF Connect. It's greyed out...
Hi,
We just received prototypes of a new board with the nRF52840 and now we have a reset problem.
When the board is reconnected after a long time (no voltage remains on...
Hello,
I am testing the multilink BLE (1 central : n peripheral) UART example.
I am using Github code and tested it.
The central example is(SDK 16.0.0):
https://github...
Hi, I've just compiled clean examples from Zigbee and Thread SDK 4.1.0 and I'm following instructions from here: I've got CLI on the nRF dongle and multi_sensor example loaded...
Hi Nordic experts:
I am working with sdk 17.0.2 nrf52840 ble_app_uart example project. I added twis i2c slave functionality in this project, and the project is working fine...
Hello everyone.
I want to assess the range of my current setup, theoretically. And I found this useful online "calculator": www.bluetooth.com/.../ (please scroll down until...
Hello,
I wanted to implement WDT resets when my application hangs. I am working on the advertiser code, what I observe was when I implement WDT driver in SDK 15.2 examples...
Hi,
I have been working with mesh and I'm using the version 4.2 Mesh SDK.As I understand it I should use nrf_mesh_serial_tx() api to send serial message.When I use this...
Hi There,
I'm working on a datalogger project using nrf52840, includes BLE also. I'm using external 24 channel ADC and should be able to log data to the SDCard at the rate...
Hi, can you explain shortly is it possible to use OTA functionality from FreeRTOS application? I wasn't able to found such an example, and I'm wondering about the possibility...
Most times the Online Power Profiler doesn't even load the graphics, etc. 80% of the time it doesn't finish loading and I have to reload multiple times. I have a 1 Gigabit...
Hello,
I'm using nRF52833 for my application. Unfortunately, my dev kit can not connect to my PC when I use cable to connect it to my PC. It can supply voltage for my kit...
