I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
I have the nRF52DK setup with SES. I can build the example ble_peripheral projects and I can run them in the debugger without any issues.
I also have a Telit BlueDev...
I have taken the examples\peripheral\serial example and made minor changes (NRF_UART_HWFC_ENABLED to NRF_UART_HWFC_DISABLED, commented out bsp_board_init).
I have a USB...
Hi
Our requirement is to do Over-the-air DFU at the bootloader level for nRF52840 devices on thread network. Can you suggest if this possible at the bootloader level? If...
I got a J-Link mini Edu today, and I wanted to try to experiment using it with my NRF52840 dongle.
To test it out I tried uploading some of my code and some examples, but...
Hello,
For a project, I'm trying to create a connection between an android phone and an nRF52832 via bluetooth after scanning nfc. But Everytime I tried it, a dialog appears...
I would like to program a nrf52840-Dongle with OpenThread's ot-ncp-ftd.hex image over USB DFU. After putting the device into bootloader by pressing the physical reset button...
We have two evaluation boards of nrf 52832 Bluetooth modules. we try to connect the modules in one to many network format for that application we flashed the following software...
Hi!
I have a Nordic NRF52840 development kit and am trying to interface with the MX25R6435F flash chip. It communicates over QSPI, so I know I have to go through the QSPI...
Others have had similar problems with pointers for structures. So, I've tried several different methods including one that was suggested in another help ticket. I am writing...
I checked the operation of the application "ble_app_hrs" and I see that the FDS makes a new record in flash memory with every new connection. What is the need and can it be...
Hello I want to use MTU = 247 bytes. For 1M PHY, everything is working fine. When I set the coded PHY, there is a problem. I get the GATT event NRF_BLE_GATT_EVT_ATT_MTU_UPDATED...
I want to tested RF performance ，so i hope send cat-M 6RB@0 signal. For example, the circled part of the picture: ,it's send 6RB@22 signal。please tell me AT command.
Re: nRF52833DK, s113 and nRF5_SDK v16.0.0
It appears that nrf_sdh_freertos.c needs to be modified to support JUST_WORKS and LESC because the softdevice_task() in nrf_sdh_freertos...
Hi
I am working this tutorial . At the end of this, I copied and executed the contents of advertising_init() function but it became NRF_BREAKPOINT_COND.
When debugging...
I am trying to use the GPS from the Thingy:91. Due to the unavailability of Power Saving Mode (PSM) in roaming with my local provider, I am considering what options are available...
