I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hello,
I have a question about Bluetooth connectivity issues. The BLE code I'm trying to make will be connected to the smartphone (Android). If phone out of the Bluetooth...
I'm developing a bluetooth device that only advertises data, it's set to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE and BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hello everyone,
Can I use the latest nrfutil 6.1.0 tool to generate the DFU zip file for the dual_bank_bootloader in SDK11?
If yes, do I need to keep the --hw-version...
Hi, I wanna enter the system on sleep to save the power up to 10uA(about tens of A). I am using nrf52840-dk with SPI LCD and some GPIOs in zephyr. Also I want to do DEVICE_POWER_MANAGEMENT...
Hi, I would like to run an nrf53 example project. I got the devkit, and after some struggle I am now able to compile and run a project.
I need to run an Bluetooth example...
This is really a question about best practice - I have some ideas of ways to do what I want, but wonder if there is some clean API-supported method that I haven't found.....
Hi, I am in design stage and i need to change nrf 8001 to nrf 52810. In this point i have a question about pin configuration in nrf52810, Can i use any pin for any use? i...
Hello everyone.
I know from Errata document that the GPS antenna soldered on DK is not working properly on the 0.8.2 version of the DK. I need to use GPS for time syncronization...
Hello,
We are allocating a large amount of pages (100 pages, ~400kB) for the Flash Data Storage module in order to hold collected data. As a result, the fds garbage collection...
Hi all, can the nRF52840 dongle be used as an external Bluetooth 5.0 peripheral via a Raspberry Pi 3 running Linux?
I received this message from my engineer
' The drivers...
This is based on the article fround in devzone here .
I'm compiling a simple Hello World and followed the instructions as per the nrf Connect SDK Turorial Part 2 .
To...
Howdy,
I'm using Zephyr to configure an nRF52840 to act as an I2C master and send data to a TM4C slave at a 100kHz clock rate. The nRF52840 appears to hang after calling...
Hello, I am working with nRF5 SDK 17.0.0 and using IAR Embedded Workbench 8.50.1. I am following the Secure DFU bootloader guide as posted here .
On Step B3, I get a build...
During development, it is a very common task to combine the 4 elements into a single hex file, softdevice, bootsettings, bootloader and application. Mergehex is limited to...
I'm using an nRF52840-Preview-DK board in a POC (Proof Of Concept) to convert an I2S-TDM bus to SPI.
So it takes the I2S FS (frame sync) and CLK (clock) signals as inputs...
