Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello everyone ,
I have question about saving the configuration of Friendship so-that after rebooting the SOC, the friendship's configuration restored without applying the...
Hi, I'm HongJae.
I'm developing a Bluetooth peripheral program with nrf52.
Briefly,
if I send a hexadecimal message(e.g 0x35), GPIO's are ON.
After 1 minute from...
hi,
I found a interesting thing：I use the output function to configure the P0.14（nrf_gpio_cfg_output(14)）. After configuration, the normal output should be low, but it outputs...
hello all,
i am using nRF52832 SoC in my project and my requirement is to write some configuration into internal flash when i flash the program using segger j link.
for...
Hello.
I am evaluating with nRF52833 DK board. I checked both peripheral/uart and ble_peripheral/ble_app_hrs.
Examples work each well on nRF52833 DK. I want to add the...
Hi support Team,
Following are my Questions.
1. Please recommend me three development boards from Nordic. I would like to build the mesh Network.For example one will transmit...
I am seeing a number of issues, but since they appear to be different, I will use different threads.
Setup: have gone to ble_blinky example to keep things as simple as possible...
Hi, i am new to the nRF52840, i like the features it has and i want to create a board using it. In the datasheet it is said to have 2 ARM processors and i want to use it as...
About 3.7V Li-Po battery on spec., can we read adc value from the battery using p0.04(A1) without external voltage divider circuits? In fact, 3.7V battery outputs 4V ,seeing...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
How can I define paths in SES (Windows), like $SDK_PATH, for my project?
- if they are defined in macros, what is the syntax?
- is there a standard variable that has a...
HI there,
I wanted to use nrfx spi with nRF5 SDK 17.0, but it was removed. I checked that in nRF5 SDK 15.3 it should be available, but when I downloaded it the example is...
Hi Everyone,
Last two weeks I'm trying to make a Real time streaming custom service on PCA10056 DK. I have modified the ble_image_transfer code according to my requirement...
I'm testing the Zigbee CLI Agent example and try to read info from my Titan wall sensor. I can read almost all info, but not values, that are using float type.
How I can...
Hi everyone,
I have an issue when i am writing to flash sometimes i get a SOFTDEVICE assertion failed just after using the function fds_gc().
The structure i write...
