I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello everyone,
I'm programming nRF52833 for my own application. In my application, I have a button to turn on and turn off the supplier. There is only 1 button so that...
Hello,
I contact to you because a customer bought the bluetooth development tool part number NRF6939, and they asked the following below;
"
Can you specify whether there...
I have been testing a sample project that has compiled and worked fine for a week. But now it is giving build errors related to Zephry.
I think a broke a configuration,...
Dear Nordic FAE and fellow engineers,
I am using a custom board with nRF52832 WLCSP and I am trying to program it via SWD using NRF52DK PAC10040, and SES for programming...
I used armgcc and built out nrf52810_xxaa.hex (file size 60656) in
nRF5_SDK_17.0.0_9d13099/examples/ble_peripheral/ble_app_beacon/pca10040e/s112/armgcc/_build
I used...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
My I2C communication...
I desgined a PCB based on the nRF52840 module and led out the SWDIO and SWDCLK pins to Micro USB.
I used jlink v9 and connected three pins in SWD download mode. The SWDIO...
We have developed a custom board based on nrf52810 SoC (package : QFN32) , after following the guides on the forum we tried to run the example ble_app_uart(pa10040e) from...
Hello, I couldn't find any examples of SPI usage with nrf connect sdk, where can I find them?
At the beginning I want to do pretty simple thing - just send array of bytes...
Hi noridc,
I am using the sdk 15.03, s140 and the nrf52840.
I used as a reference the ble_app_interactive experimental example and the ble_central/ble_app_hrs_c. My...
Dear Community, good morning
I am working in a design that do not use USB port. If VBUS pin is left floating could it cause any issues to nRF52840.
Best regards,
Hello, guys!
I have some questions concerning GPS receiver inside nRF9160. You say in your documentation that GPS receiver supports L1 C/A reception - link .
There are...
What's the easiest way to view all logs and error messages using USB serial connection app like putty, on the nRF52840 dongle?
What drivers and functions do I need to enable...
What level of risk is involved with brownouts for the modem? We have seen some modems in the past which have bricked themselves when a brownout has occurred when performing...
Hello, I want to inquire about the functionality of nRF52833-DK if I want to communicate between transmitter and receiver for locating position of receiver using BLE (Bluetooth...
