Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi there,
I'm attempting to link in a static library archive to my nRF52840 targeted project and receive the following error: Exception table sections and plain sections...
when I use Jlink viewer for tracing, found a fatal error:
1 code:
static void lfclk_config(void) { uint32_t err_code; NRF_LOG_INFO("enter lfclk_config"); err_code = nrf_drv_clock_init...
I have been playing with the nRF5340 and specifically the HCI-RPMSG.
I have looked at these files below. They all worked when programmed in the nRF5340.
When viewed in...
Folks,
System Info : MacBook Pro (10,1; 15" Retina, Early 2013), Running macOS 10.15.6 "Catalina", with 500GB SSD, formatted with APFS, into a RO system partition and a...
I've made a circuit using the NRF8001 but slightly deviating away from the original PCB example. I'm getting the device to go into "Advertising Started" but I can't pick up...
hello Nordic
i have s SOM which i want to use nrfutil in it for FDU via UART of an application i have on nrf52832, s132 v7.0.1
i have the bootloader flashed with the...
Up until now I have been the sole firmware developer and the keeper of the keys for our product.
Our scrappy little startup has expanded and is now bringing on additional...
Hi,
Problems I am having with PWM:
1. Using app_PWM and GPIOTE to start and stop the PWM: When button is pressed, GPIOTE handler sets a flag that is polled to start the...
I am using Timer0 and Timer with GPIOTE and PPI to output 2 clocks on 2 pins.
Both timer settings are identical (for troubleshooting). Only timer-0 can be generated at the...
I am working with nRF Connect SDK using an nRF52840 DK. And I want to realise both BLE mesh and FOTA upgrade. FOTA upgrade example SMP Server Sample works properly for Bluetooth...
To parse information from strings I want to use sscanf().
Currently I have this small test program:
And in the prj.conf I have CONFIG_NEWLIB_LIBC=y defined.
This program...
Hi, At power on lots of MUCBoot prints pop out of the UART:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1 *** <inf> mcuboot: Starting bootloader <inf> mcuboot: Primary image...
Hello -
We are developing an application for nRF52840, using the v17.0.0 SDK. The application is running on FreeRTOS. We need to power off all the RAM and use the RTC...
Hi, I am trying to get bootloader to jump to either application 1 or 2 base on button states when booting. I am not sure how do it properly. One of the applications is using...
I created an Azure IOT Hub and simulated a X.509 device using C and device SDK for Azure .
No problems here.
Then I run sample nRF9160: Azure Iot Hub and receive the...
