Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
in https://devzone.nordicsemi.com/f/nordic-q-a/24115/io-pin-signal-during-reset it is mentioned that the pins of the nRF52832 get set to input _during_ a reset.
...
This is my RTC init function. Whenever I start advertising in fast-advertising mode, and timeout for fast advertising expires, the RTC2 timer stops running and COUNTER resets...
Hello,
I am trying to make a simple power optimized BLE peripheral device based on nRF52840.
Here is the chart from the Power Profiler
The device advertises once in...
Hello,
I am trying to use "west" command in Eclipse but I am not able to do it.
I was able to do that in Visual Studio though.
I found this link https://devzone.nordicsemi...
Hi,
We are trying to configure the WDT and are running into issues. The plan was have a timeout of 30 seconds when running and then 24 hours when sleeping. Note we are...
While developing the power supply for edge cases of NRF9160-SIBA we encountered problems with both the continuous and peak current consumption, mostly during startup. We are...
I have a question on stack guard that I tried to enable on nRF52840 and hope you can give me some pointer to verify it is functioning properly.
Basically, I call nrf_stack_guard_init...
Hello i am making an application using hid over gatt. i changed original keyboard usb description with fido description for test, however, i don't get any event through. I...
the link i given below tells, how to make a haptic glove using arduino mega
https://hackaday.io/project/160405-diy-haptic-glove-for-vr
i want to do it with nrf52840 DK...
Hi everyone,
I'm working on programming nRF52833. I want to my nRF52833 is able to broadcast advertising and also scanning (In another word, my device plays peripheral role...
Hi
I have upgraded from an early version of SLM to the latest version in nRF Connect SDK ver. 1.3.1
the SLM application is running on a custom board with a nRF52840. Using...
I found this application very useful!!
The code is now at the Github.
I found there are some problems to reconnect - it gets many errors and the peripherals eventually...
Hi, I understand there's no high level TWIS (i2c slave) driver for nRF9160 (i.e. in Zephyr); as such, I need to use TWIS driver that's part of nrfx, or even lower (HAL) level...
Hi,
I need to upload compiled binaries from mbed studio to my custom board based on nrf52840 using nrf52840 dk.
I have replaced the jlink software( J-Link OB-SAM3U128...
