I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I'm calling nrf_drv_uart_rx_abort() in order to read partially captured input from UART in my event handler.
However, instead of receiving a NRF_DRV_UART_EVT_RX_DONE event...
Hello,
We are currently developing a project based on nRF52810.
We are testing some examples to learn more about this chip.
Now we would need to know which signals and...
Hi,
I have gone through this ticket --> https://devzone.nordicsemi.com/f/nordic-q-a/30104/how-do-i-share-private-questions-with-my-coworkers-using-the-new-devzone
But...
Hi,
I am using NRF52840.
After upgrading to SDK 17, I found that the chuo stays in boot mode because this new condition (I highlighted it in the code below):
if (NRF_BL_DFU_ENTER_METHOD_GPREGRET...
Hi
I have some questions.
I'm trying to communicate with BLE using 9160DK with my smartphone.
1. Do you have a simple example? 2. Can I send videos or pictures using...
Hi nRF support team, By using the nRF Connect SDK, I am trying to create a timer, which I can use for incrementing a counter by 1 for each second on a timer interrupt handler...
Hi,
I am trying to merge the ble_app_becon with dfu. What are the things I need to add. In becon example I don't find the services_init() function. Do i want to include...
Hi,
I am using the latest SDK, with the nRF52840.
using the usbd_ble_uart example.
Created a timer that starts to send packets to the PC throw USB with a running index...
Hi Dev Team,
I have an iot.1nce.net sim that I am using in Germany.
+CGDCONT: 0,"IP","iot.1nce.net","10.205.84.3",0,0
I was trying the eDRX configuration using a basic...
Hi,
The ' nRF52840 Errata Attachment Anomaly 172 Addendum' linked to in the nRF52840 errata (Version 1.3, page 17) seems to be missing; the link gives a 404 error. Where...
I've tried to test the ZigBee OTA example on the 4.1.0 SDK, but it does not work. I've gone through the exact steps of the procedure as described in the infocenter, but it...
Hello,
in our project we have a nRF52840DK as central (s140) and a custom board with nRF52832 chip as peripheral (s132). The software on the nRF52840DK is based on the ble_app_uart_c...
When I program the Zigbee cli example from T&Z SDK v4.1.0 I see that the Zigbee stack uses some flash areas at the end of the chip. In my case 304 bytes @ 0x000F7000 and 24...
Hello,
Using libuarte I have been able to set up UARTE0 and UARTE1 for main communications, and debug communications respectively. While using UARTE1 to print out debug...
Hi,
I's trying to implement switch two application firmware in the openbootloader example, but I meet some issue.
I change the sector to 0x27000 in App1, 0x40000 in...
