Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
hi，i want to control a led driver by frequency send iic data, i need send 600 bytles once at least 10ms each time ,and the 600 bytles send by 3times.send the 600 bytles need...
Hello, how can I increase LOG backend queue size? I was comparing some sdk_config settings with some examples, but did not find difference and the example does not fire this...
Hi,
I am trying to capture a modem trace to send to Nordic for analysis, however Nordic says they are unable to open the ones I've captured so far. I am using the NRF9160...
Hello,
We are upgrading a nrf52832 project which is based on SDK 14, soft device 5. Currently we depend on dual bank DFU operation but our application. Unfortunately we...
Currently working on flashing the bike power tx example to my Arduino Nano 33 which uses a NINA-B306 nRF52840. The device is wiped clean with only the s340 softdevice loaded...
I am trying to run one of the examples in the SDK (...\nRF5_SDK_11.0.0_89a8197\examples\peripheral\blinky\pca10028\s130\arm4) with the name "blinky_s130_pca10028" but its...
Hi, I am starting to developing applications for the nRF5340. I am interested in exploiting the added functionality that Bluetooth 5.2 provides. I want to use a smartphone...
Hi,
We have an unusual problem involving FPU interrupt clearing and battery charge state on the NRF52832.
We are applying the following fix to reduce power consumption...
I am really struggling with getting started with software development of the nrf52840. I have looked at the SDK but I don't understand where I can find what SoftDevice I need...
Hi Devzone!
I'm preparing the certification for the product which uses nRF52840 to sell in Korea.
I need to know if it provides BR/EDR or BLE only.
Best regards...
Hi ,
I am using nrf52840 dk running zigbee cli example in sdk . I have configured dk as coordinator and using xbee modules as routers . After successful addition of xbee...
Hello All,
I am working on nRF52832 custom board.
In my application I used i2c and spi both, so I implement i2c and spi in my application.
My problem is when I implement...
Hi everyone!
While testing ble functionalities, I have noticed random resets during advertising operations.
My custom board is defined to make infinite advertising periods...
I am following https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/thread_border_router.html with raspberry pi 3B+ and NRF52840DK as NCP for boarder router connected over...
Hi,
I am using NRF52832 with SDK17.0.0.
I want to use app_uart module without physical TX/RX pins.
Cause I just want to utilize fifo module to handle data through bluetooth...
