Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
We are using Jlink and nrfjprog to program the nRF52832 flash via SWD interface. We have a combined hex file which is about 512k and takes about 12 seconds to flash...
I am debugging my applications transitions to SYSTEM_OFF and back again. I am connected to the debugger so I am presumably testing with "emulated system off" which is just...
Hi all,
I wrote a nice library for using an offboard SPI flash chip and am now trying to port it to our master code which runs on freertos.. I wrote the library starting...
hello ,i am using sdk16 with nrf52852 DK i can be able to get time using that nrf calendar example. Now i want to sync up the mobile time with Dk every time i connect with...
Hello, i'm developing some boards with nRF24L01, everything was going fine, i was able to write and read payloads back and forth using modules mounted on 4 different hardwares...
Hi,
We were trying to bring up NB-IOT with a Jio SIM ( India). Seems it is able to connect to network, but no data connection. The sim vendor said to us we need to use ...
Hi all,
I cannot manage to get a proper System Off consumption with the nRF52840.
I use this setup, with devkits as the DUT (powered through "External Supply") :
...
Hi all,
In my current project I have 7 sensors, each hooked up to an own nrf52. I am polling between 8 and 28 byte(depending on operation mode) of data in 10ms intervals...
I created a copy of bluetooth/peripheral example and copied the nRF5340DK board files to make my custom board definitions. The guideby Øyvind A. Sandberg is really good here...
Hello All,
I'm interfacing a temperature sensor ds18b20 with nFR52840, which uses one wire protocol.
I'm using this repo https://github.com/DSysoletin/nrf52_ds18b20_example...
Hello! I wrote my own version of the bootloader for nFR52832. If I go into the loader, check the application and switch to its execution via nrf_bootloader_app_start (), then...
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_clock_init (referred from main.o). .\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_clock_lfclk_request...
I need to adjust the Flash and RAM to accommodate bootloader and Softdefice and read the tutorial at the link https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting...
- I reviewed Android-nRF-Mesh-Library code, and i saw this logic: first, it used Provisioing Service, when provisioning is completed, it disconnected with nrf board, and then...
Hi!
I'm developing code for Central device on nRF52840. SDK 16.0.0 SoftDevice S140.
Peripheral is a Bluetooth mini printer. I can connect to it and print. But when I try...
