We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
I am working on a project with nrf52832 and LIS3DH for a beacon.
I have added the low power feature into my application to go to standby mode in case of inactivity...
Hi,
We are currently testing the fuel gauge firmware from the nRF Connect SDK but are encountering difficulties integrating it with the u-blox B206 module. Could you provide...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hello,
I am looking into the market for PMICs for 3V primary coin cells, for use in (somewhat) remote IoT devices.
It is exciting to read about the new nPM2100. I already...
Hello, With respect to my previous post, I am trying to use the nrfx_pwm_simple_playback function to run sequences continuously for an RGB led. Initially I did not fully understand...
Hi
I ve to use nrf pwm common mode feature, and there is sample code under project name common_mode_test, but i am unable to build it either with ncs version 2.9.1 or 3...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
We used nRF5340 as the controller to develop a product for our customer, which requires a QSPI interface of 5340 to drive a screen. However, during testing, we found that...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi,
I am currently making an upgrade og a nRF51422 project that has both BLE. and ANT+ Cycling Power profiles and if I run the old project on an 51822 processor I can see...
Hi,
I try to migrate a working nRF53 Zigbee project from SDK 2.7 to the latest SDK and an nRF54. As described here, I also switched to Zigbee R23. The project structure...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hi,
We are interfacing WM02C (nRF7002) with LPC55S69JBD100E as the host controller.
1. Could you say how to select the 2.4 GHz and 5 GHz antenna selection by hardware...
Hello, we are using a BLE module nRF52832 (MDBT42-P512KV2).
We also add the external 32768Hz crystal to our application with this module.
However, we recently found that...
