HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
I have beacon (ble_app_beacon) transmitting every 40...50 ms, nRFConnect shows adv interval is ~44 ms, so it receives ~22 msg/sec. My beacon listener gets only 10...12 msg...
Hi,
I have simple test firmware that simply connects to the network and goes into PSM sleep, it works perfectly well on the nRF9160DK but the Thingy 91 is refusing to connect...
This is a really basic question, but please bear with me. This is my first time foraying beyond the world of Arduino! :)
I'm attempting to make an ANT+ bicycle power meter...
I am using nrf52832,I have Defigned "CONFIG_NFCT_PINS_AS_GPIOS"as below。P0.09 is configed as POWER_HOLD pin, P0.10 is configed as buton.
I found that when I download softdevice...
Dear Members,
For scanning GSC10 sensor,
can this example be used ?
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ant_examples_scanning.html
Thanks
Hi,
I am currently working on the project that involves Pre-certified Bluetooth Module (SG Wireless SGW1110 CE & FCC certified, based on Nordic Semiconductor nRF52480)....
I am getting an intermittent "Softdevice assert: 151994:0" error on device initialisation or after the device has run for a period of time. I am using Light Switch Client...
Is there a way to generate a square wave like the one in the picture without using any kind of interruption to change settings middle-wave?
For example, the wave can be...
Hi,
I have been able to use the NRF-9160: Cloud_Client sample for sending data to my AWS IoT MQTT broker on PSM mode from my Thingy91 with a CLOUD_MESSAGE_PUBLICATION_INTERVAL...
Hello, I am trying to implement my own custom bootloader in the nRF52811. I have the softdevice loaded, which then jumps to address 0x19000. This is where I put my bootloader...
Hi,
I'm using nrf52833, flashed by using Jlink SWD programmer. I have no probleme to re-programmed 2/3 of my board.
But the hird gave an error. The strange things...
I am using the gazell protocol of nrf52840 to achieve some functions,but I don't know how to understand the protocol code deeply,anybody has advice or flow chart or relevant...
I want to implement noise sensor based on PDM (pulse density modulation) , But I cant found any PDM driver or API based on Zephyr , I used MP34DT05(st semi-conductor).
So...
I have nrf52832 radios communicating with each other 100%. I have a nrf24l01p that is the 'gateway' to which the nrf52832 sends dump data. I can communicate with nrf24 and...
