My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi,
We thought to have a setup like this
1<-->2<-->3
1 is MESH ADV device with some mesh model
2 is MESH ADV + regular BLE stack support
3 is Gateway with...
I am trying to collect sensor data and store in flash using qspi interface. Unlike the peripheral example code, the qspi data handler function is not getting hit with ble...
Hello, I have another problem... i work on nrf9160 dk
I try to send http post when i pressed button 2 but this doesn't work.. Below you could see my code who block on printk...
I have been reviewing this merge: https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/1982 and it appears that there is capability in the fota example to enable https...
How to configure the start address and size of flash memory and nrf52832 in SES and how to calculate the size? How to calculate the start address and size of app and bootloader...
Hi,
Current Status:
I'm trying to run the fpu_fft example from the SDK 15.3.0 on my nRF52832 DevKit. When I clean and build the project in SES everything is fine and I...
Hi, I have a question about unknown flash data from MBR area which start from offset 0x0000035C, 20 bytes data show as below.
Data[20] : FF FF FF FF FF FF FF FF FF FF FF...
There doesn't seem to be any validation of the image when updating the bootloader by secure DFU. nrfutil has no switch to generate any crc or ecdsa_signature. The code uses...
Hi
I am making mesh network using Raspberry pi and NRF52 DK. I install bluez 5 and meshctl on raspberry pi. I successfully connected nrf52 dk using bluetooth. I attached...
I am doing this nRF52xx-to-Thingy-52 example: https://github.com/crfosse/Thingy-52-to-nRF52xx I am able to get the led part working fine, but when I finish the instructions...
I am trying to merge Softdevice, bootloader, bootloader setting and application. But unable to do in a single mergehex command. If i do merge seperately ((BL + SD + APP) with...
Hello.
This function from Zigbee SDK 4.0.0 changes configuration of already configured input pin by calling nrf_gpio_cfg_default(ERASE_PIN);
The leds_buttons_init()...
I loaded up pca10056e ble_app_beacon example for SES to test it on a custom nrf52811 device I have built (using BMD-360 module).
I followed the instructions here and removed...
